Jump to content
SAU Community

Recommended Posts

Just put the lightweight shockproof redline oil into my gearbox today. Now I can easily change to 2nd gear when the car is cold. But, I feel crunches for 1st, 2nd and 3rd gear, even when the car is warm. I think that it's worser than before. The crunches is absolutly noticeable.

The old oil that drain out from the gearbox is something like auto transmission oil.

What happen to my gearbox that react with the redline oil like this? any ideas?

:shake:

Link to comment
https://www.sau.com.au/forums/topic/13926-i-feel-worser-with-redline-oil-why/
Share on other sites

Give it an easy 1000km+ before you make up your final decision on the Redline Oil.

For the first few days I was like "mannn i paid $100 for this stuff".... but now 5000+ km on and its the best $100 I've spent on my car.

yeah give it a good 1000km or so.

i used to get crunches into 2nd, they went away after about a week of driving after putting in lightweight shockproof. then about a month later, shifts became nice and easy, i have a short shift kit and shifts used to be really tight, too tight, now its just nice.

Yes, maybe the clutch adjustment problem. Everytime when I change gears, I will depress the clutch pedal all the way down. But, I only need to release it a little bit and the clutch start to engage.(car start to move)

And I found that the clutch fluid level is in the middle of the "max" and "min" mark. Should I put more clutch fluid in it? And what sort of fluid should I use to top up? Can it mix with different brands?

Or should I change all the fluid? if so, how to do it?

Thanks!

What I tend to do as a standard to my car is that " If the item and or fliud is unknown best to change it with a known item."

This way I am able to control what goes into the car and not to worry anymore. In the case of clutch and brake fliud fresh is best naturally. If the fluid has been sitting around in the garage or in a car for a few years they tend to absorb water leading to corrosion in the lines down the track.

MoonButt

  • 1 month later...

Hmm, perhaps you should have used Redline MTL or MT90. They are the ones that were designed from the start to give you better shifting, not Shockproof (even tho it does a good job too).

If it was ATF, it does give good shifting being really a hell thin viscocity, but it ****s up your box pretty badly after a while, because ATF does not contain the proper extreme additive protection that gears require.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...