Jump to content
SAU Community

Recommended Posts

A stock dump pipe flows the spent exhaust gases from the turbo and wastegate through the exhaust system (cat, resonator, muffler etc), the screamer pipe directly vents gases from the wastegate into the atmosphere. I'm guessing you have stock internal gate turbo, so you can have a screamer pipe but it requires a partition between turbine wheel housing and the wastegate for seperate dump and screamer.

Advantages of a screamer pipe: THEY'RE FUGGIN COOL!! and get they the attention of everyone when the wastegate cracks open at full boost, they also reduce turbulence and backpressure in exhaust system.

Disads: Illegal, very loud

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2601576
Share on other sites

Explaination of the setup is in the above post... so here is a bit more.

For a stock turbo or otherwise internally gated, pointless.

Only really useful when using a properly setup external gate arrangement.

On a stock or near stock turbo they sound dreadful as the internal gates are tiny, and it simply (performance based) doesnt offer a gain as there isnt enough flow coming out of the turbo that a normal internally turbo with a good flowing 3" exhaust cant handle.

If you do have a larger (int gated) turbo, and you are having issues with boost control, then the cause is the turbo itself... and it should be fixed there, not with an ext gate/screamer

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2601622
Share on other sites

So far in my car i have these mods:

apexi power fc

3 inch exhaust cat back

front mount

z32 airflow meter with apexi pod

12psi

do you reckon it would be worth putting a dump pipe on for now until i get a bigger turbo to put a screamer pipe?

Also what power gains am i looking at if i put a dump pipe?

Also if i put a bigger turbo would a screamer pipe get good power compared to a dump?

Also SINISTA are you running that off a stock turbo?

Edited by 4AL2NV
Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2602447
Share on other sites

Why are you running a Z32 on a stock turbo'd car...

Dump pipe is quite important.

Dont both with a screamer/ext venting pipe dude, its pointless, if you read my post... apply that to the "bigger turbo" scenario and you'll have your answer

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2602621
Share on other sites

i had a screamer pipe on a stocko turbo on a 20 in one of my old cars, it actually hindered performance but sounded tuff as (ie like it had an external gate with screamer pipe). it was a hks item :) . screamer pipes make your car sound 10 times as loud at full boost, i swear i came every time it hit full boost :D

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2604452
Share on other sites

i had a screamer pipe on a stocko turbo on a 20 in one of my old cars, it actually hindered performance but sounded tuff as (ie like it had an external gate with screamer pipe). it was a hks item :) . screamer pipes make your car sound 10 times as loud at full boost, i swear i came every time it hit full boost :D

How did it hinder performance?

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2604458
Share on other sites

i had a screamer pipe on a stocko turbo on a 20 in one of my old cars, it actually hindered performance but sounded tuff as (ie like it had an external gate with screamer pipe). it was a hks item :O . screamer pipes make your car sound 10 times as loud at full boost, i swear i came every time it hit full boost :(

This is very true how it sounds and performs is directly related to who its been made by and how much development has been put into it and not wether it is an internal or external.

Link to comment
https://www.sau.com.au/forums/topic/139578-screamer-pipe/#findComment-2604883
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...