Jump to content
SAU Community

Recommended Posts

Powertune sent me a 38 instead of a 44 that I asked for.

The 6boost manifold is for a 44. So i just gotta make an adaptor peice so it can all fit together.

Don't do it. Get the 38 swapped for a 44. You will regret using the 38

ummm also i pretty sure the 38 use the 44 foot.... they just have an insert to make it 38. might wanna check that. the out is 38 but im sure the in is 44 with an insert to make it 38 ;)

I think you are referring to the valve seat. Both have it I think

I got in contact with them today. looks like Im exchanging it for the 44. Thanks for your help, Dan.

Cool mate no worries. I'm not saying you WILL have problems but the chances are fairly high from what we see. Bigger gate is always better and if they are just going to swap it out, it's going to make things a lot easier, not only for boost control but also for fitment by the sounds of it

Just being a dick............

sort of would love to throw some Tial rear housings on the -10's and convert to external gate..... mainly for the whoosh / screamer noises. but eh, that's a lot of effort required.

Just being a dick............

sort of would love to throw some Tial rear housings on the -10's and convert to external gate..... mainly for the whoosh / screamer noises. but eh, that's a lot of effort required.

There are no bad ideas, only bad execution

As far as i know to go the tial housings (no internal wg) id need to get vband dumps made and then work out how i was to plumb the gate/gates onto it all. Custom manis / gates on rear housings

Too much money to really convert imo. Easier to go highmount 30's or just a 51R / 4202 with split pulse!

But i do agree!

Edited by Force Fed

Ben Earl if you still lurk here- Stance Nation fb page just uploaded the sweetest pic of your 32 and Jordans R33 and another guys R34 can't remember his name. Has thousands of likes and tonnes of comments. Must be good to be recognised across the globe man!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...