Jump to content
SAU Community

Skyline vs LS1 vs Soarer dyno day 17th May

Martin Donnon

By Martin Donnon,
in South Australia

 Share

Recommended Posts

  • Replies 130
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

>>M1_IMPORTS<< Enthusiast

>>M1_IMPORTS<<

Posted
Posted

wow!! look like everyone has pulled out... well that about the same story with most of my mates that put their cars down on the list :P ....

I guess we beter make the dyno day some other weekend.

So, my appologies for pulling out so late but I will have to miss out on this one.

For all the people going 'have a great day'!

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

I'm not impressed with all of this at all .... except for Matt that has a serious family emergency, it's not fair to say you'll support something then back out at the last minute. It bodes very badly for future events and where will we be then? Why go to all the trouble of organising something only for people to say they're going to turn up, then back out at the last minute. (And I wasn't even involved in organising anything btw).

/end rant

grepin Experienced

grepin

Posted
Posted

Its a damn shame. We have to support organizers of events especiallly tuning shops as they have the backing to kick these things off. I know its an opportunity to drum up buisness, makes sense. Interstate seem to have a lot of events such as track days quite often - something I would like to see more of or should I say see at all. Morpowa are doing the right thing. RPM are doing the right thing. JMS drift days. Tilbrooks has events for SVD as a sponser. I hope this is a good day with reasonable numbers as I would assume Morpowa will think twice later and we will end up with nothing. I know people had legitimate reasons however it would be sad if people are leaving to follow others.

Just thought it should be said.

grepin Experienced

grepin

Posted
Posted

Timmaay.

Have a go. Then at least if you do any mods you have a baseline to start from. I am new to Skyline/Nissans for the last few years converting from V8 Commodores so I am intersted to see the older cars. Not embarassing at all. You could say I might be embarassed by GTR's its all relevant.

whatsisname Grand Master

whatsisname

Posted
Posted

Very well said Greg (grepin). To be honest I didn't have any reason to do another dyno run 'just yet', but "was" intending to go to support SAU involvement. A recovering wife would've become ex-wife if I did.

It's workshops like RPM, Morpowa, Tilbrooks etc that are instrumental in helping the import scene grow in SA. We, South Australians, are very lucky to have the number of decent import specialist workshops that we have, given our relatively small population/size.

Talking of dyno runs, I will be hitting the dyno next Wednesday. Got a new custom dump pipe being made & the dump/front fitted with heat wrap. Add to that a few other exhaust system changes & tune tweaks. Should be a touch louder if nothing else :P

whatsisname Grand Master

whatsisname

Posted
Posted
Originally posted by Freebaggin

Whatsisname,

Hope all is well this weekend for you & family.  

The mods sound great.  RPM doing it?

Yep guys Tan is well :( Not as mobile as she'd like atm but getting there.

The lastest round of mods & dyno runs are being done at RPM. I'll be spending the day getting my hands dirty too (polishing stuff mostly). It would be nice to see a dyno run on the Morpowa dyno to use as a comparison, Martin would be the man to see for this ;)

Graham,

Hope your wife is doing well mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...