Jump to content
SAU Community

Recommended Posts

I have a fujitsubo 3inch cat back and it sounds good.But all other skylines i hear sound angrier and throatier,not to mention louder. Why is this? Will a dump/front pipe make my car sound better? Im after the cool RB sound that is unmistakable. Anyone got any suggestions?

CHEERS

Do you have a cat?

Ans:

NO: Then probably make no differance

YES, but std:This will be drastically restricting flow, thus will be suffocating engine and robbing you of power.

I myself use a legal hi-flow cat.

My car gets very angry in traffic and yells its head off when it finally breaks free.

I like the noise but the resinating in the car sometimes gives me a head-ache.... ;)

If you want load and angry.....straight through custom 3" pipe and hot dog with no silencer.

If this is too load get a 3"resinator put on like me.

;)

Mine was just a split dump, cat then straight through to cannon.

I had to have a resonator added , the drone in the cabin was just far too unbearable. When you hit the right rpm the whole cabin would just vibrate.

No not yet but wouldnt that make it quieter?

In all probability, no.

Most mufflers work by slowing down the exhaust gas. Taking energy out of the exhaust stream reduces the noise it generates when it exits. I'm sure you've noticed that most aftermarket exhausts that are less restrictive also tend to be louder than stock.

If the cat is less restrictive to flow, its also muffling less.

I had a JASMA certified Fujitsubo cat back with centre muffler/resonator and final oval muffler with standard dump/front/cat and it was also noticably quiet when putting arond but had a deep clean note when opened up. Anything but a bark. You'll notice a lot of the cars you see with a "bark" are NA.

Dont know about other aftermarket Jap systems but what I noticed with my Fujitsubo system was that it was extremely heavy due to the fact that it was extremely thick steel, which I think helped quiet it down. I reckon it would of been 3mm thick, if not more easily as it had a decent chunk taken out in one part at least 2mm deep and it had not made close to a hole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was just driving into work and while on my drive, I went to accelerate and noticed the car would sputter/hesitate and I’d hear a few pops from the exhaust before it started going faster. Then I also noticed that when I push my clutch in, the car would die. This all started happening today. Any ideas?
    • That is a lovely Volvo, just saying. Yes I should have got an 260RS when they were cheap. I do regret now.
    • ^ lots of good points made above. The thing is, "aggressive" or "flush" fitment is relative depending on how much you have been influenced by social media. My starting point is always "look at the Nismo RWD specs". That is where you should start, then start measuring as GTSBoy as sort of mentioned, because every car will be slightly different. My 8.5"+35/9.5+38 will not be "flush" enough for you because you want more "pumped" look, which is why you measure. Tyre sizes and brand/models also make a difference. Some tyres are more chunky/square, some are more rounded. That means you could get away with more aggressive offsets without rubbing. But then it also depends on your ride height. Also depends on how much your car copped damage before being shipped from Japan. So it goes back to measuring your car yourself and determining what can work. Those Nismo specs are used bacause it's a safe spec for standard car (suspension. body) with chunky tyres. But then I put 265/35 wide tyres on R34 GT-R wheels, and currently run 285/30 tyres on 18x10 wheels.
    • Sounds pretty awesome. I recommend creating a new build thread and posting all your goodness in there.
Ɨ
Ɨ
  • Create New...