Jump to content
SAU Community

Recommended Posts

Give regency a ring.

I did some time ago and was told you are not allowed to touch anything that is concerned with the bov, being; the bov its self, the cross over pipe, the pipe that runs from the bov to the turbo inlet pipe AND the turbo to afm inlet pipe.

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2625712
Share on other sites

Give regency a ring.

I did some time ago and was told you are not allowed to touch anything that is concerned with the bov, being; the bov its self, the cross over pipe, the pipe that runs from the bov to the turbo inlet pipe AND the turbo to afm inlet pipe.

Thanks i just imported an r33 gtst and it has a blow off valve which you can hear quite easily i haven't had a chance to look but i assume its after market i wondering am i going to get defected for it should i get another quite one cheers

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2625769
Share on other sites

Yeh ive got an R33 Gtst and its got a stock blow off valve and an apexi pod......u can very easily hear the BOV noise, sounds sweet! but yeh its probably a stock BOV coz wen u import ur car and it gets complied dont think defectable mods to ur car are allowed. :rofl:

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2633109
Share on other sites

yeah, crankcase emissions.

More so how it plays with the afm and dumps fuel.

I blocked my bov off when testing if it leaked and found it would pop and fart & occasionally stalling.

Venting the air would play havoc with the air metered even more so.

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2633946
Share on other sites

I asked regency about aftermarket plumb backs.. I was told no, its part of emissions so I can't touch it.

This was some time ago.. Give Regency a buzz and see what their stand is on it these days.

Just block the std off and enjoy quicker turbo spool and almost zero lag between gear changes.

As mine spools so soon it caused a few driveability issues but nothing I couldn't work around.

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2634556
Share on other sites

um...a BOV (or recirc. valve) increases response in some cases, yes the air is released and that air does need to be replaced causing lag, but at the same time, the air not being vented without a BOV is forced back towards the turbo going the oposite way to the turbo causing the turbo to slow down quicky and to spool to the turbo up again takes time, creating lag.

Link to comment
https://www.sau.com.au/forums/topic/141001-bov-legal-in-sa/#findComment-2634634
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...