Jump to content
SAU Community

Rb25 Turbo Differences Between Models?

eXc

By eXc,
in Engines & Forced Induction

 Share

Recommended Posts

eXc Mentor

eXc

Posted
Posted (edited)

Hey Guys,

I've spent the last 2 hours searching and can't find it.

Can anyone link me or;

1) tell me the differences between the R33 turbos.

2) Which one is best suited to the RB20.

3) I know you need to make sure you get "the elbow" for the conversion...but what is it? What does it look like?

4) Any other things I should do first? Fuel pump perhaps? Will I need a SAFC or similar aswell?

Cheers

Chris

Edited by eXc
r32matt Collaborator

r32matt

Posted
Posted (edited)

Hey,

Get the R34 Turbo!

I have a R34 Turbo on my RB20 and it runs really well! Bolted straight on and used the RB20 Actuator to get the stock 10psi. Boost starts just before 3000revs and Full boost comes on just before 4000revs. :D

Edited by r32matt
salad Veteran

salad

Posted
Posted

1. i dunno but i would like to find out. i recently just too my S1 turbo off and replaced it with an S2 (because the S1 was rooted) and noticed that the design of the compressor wheel was a little different. the smaller blades did not protrude past the tip of the bigger blades.

and the S1 has a steel compressor where as the S2 has a nylon compressor

2. the S2 is supposed to spool faster due to the lower rotational mass, and seeing as rb20s cant spool turbos well, this would be better.

3. the elbow is the compressor outlet. go have a look at your turbo, it is the first pipe that comes off of your turbo, and goes into your intercooler piping

4. fuel pump is definitely a good idea, and you really should do it, just in case. another good bang for buck mod is to get your ECU remapped. cheap and just as effective as stand alone ECUs. and come with all the stock knock sensors, cold start crap etc

123456 Proficient

123456

Posted
Posted

The r34 turbo, is pretty laggy i think (has the same sized exhaust wheel as the vg30). In first it doesnt start spooling to about 3-3.5k so it makes taking off sort of hard, it does kick in hard at about 4.5k though. The performance increase wasn't all that great for me, i got a remap at the same time and achieved only 164 rwkw (on the same dyno, that i had had it measured, close to stock, at 133rwkw)

i will upgrade to cgc hi flowed series 2 r33 turbo soonish

Unless i get off my P's before then, and can get a GTR

salad Veteran

salad

Posted
Posted (edited)

S1 is definitely still worth it

easy to tell the different compressors, one is aluminium and the other is nylon. they feel much different

and the number on the comp cover is different

i think the S2 has 45v4 and S1 has 45v3

may need someone to confirm, thats just going by my crappy memory :D

Edited by salad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • AdiR34
      Pops when backing off throttle, rough-ish sound through rev range.

      By AdiR34 · Posted

      Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Roy
      Ben's R32 Gtst Build

      By Roy · Posted

      Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • MBS206
      Another little story of weird shit happening

      By MBS206 · Posted

      Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Shizu
      Returning after a long time!

      By Shizu · Posted

      Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
×
×
  • Create New...