Jump to content
SAU Community

Recommended Posts

My calculations are as follows: 1PS = .7355KW thus 579PS = 425KW and YES this must be measured at the crank.

Hi Elithar, if the engine is in good condition and the tuning is good, there is no reason why the RB20 won't make the same max power as an RB25 with the same mods, condition and tuning.  So almost 200 rwkw is entirely possible.   Average horsepower is of course a different question entirely, the RB25 is after all 25% larger.

Hi jezzrrr, let me use my sceptical bone here, what if the only reason the HKS supported workshops are using GTSS's is because it's "new" and there is money to be made.   What would be the point of pushing 2530's?  They are "old" news and everyone knows that "newer" must be better.

Looking at the GTSS power claims, 579 rwps, that's around 310 rwkw.  I have seen 330 rwkw out of a pair of 2530's locally in Shoot Out mode on a Dyno Dynamics.  But the extra 20 rwkw is not the point, it's how it gets there that is important.  Somewhere around I have seen the dimensions of GTSS's and they looked remarkably similar to 2510's.  The HKS ratings are;  

GTSS 300 ps

2510 310 ps

2530 320 ps

2535 340 ps

2540 350 ps

2540R 370 ps

2835 380 ps  

HKS rate the GTSS lower than a 2510, and I have driven a GTR with 2510's and it was awesome up to 7,000 rpm then it went flat line.  It felt like it had some boost just above  idle rpm, which is totally alien in a GTR, where the real pleasure for me comes from giving them a rev.  The guy who owned it loved it like that as he just stepped out of a grunter 6 litre Commondoor.  If HKS (and Garrett) had found a combination of compressor and turbine that gives a GTSS the bottom end of a 2510 with a slightly better top end, then for some people that would be perfect.  But I keep going back to the fact that HKS don't rate them with the same max power as a 2510, therefore they themselves are saying GTSS's have a lower top end than 2510's.

So, like many others, I await Merli's results with great interest.

  • Replies 283
  • Created
  • Last Reply

Top Posters In This Topic

I can recall a post from someone with some credibility on these forums claiming that

we typically see 50 kw losses through 2 wd Skyline and 65 kw losses in 4 wd
. Taking that off the 576.2ps (423.79kw) gives you 358.79AWkw. Quote some number.
I can recall a post from someone with some credibility on these forums claiming that . Taking that off the 576.2ps (423.79kw) gives you 358.79AWkw. Quote some number.

Absolutely, I went for a ride in a car with GTSS's and it blew me away, it was a RB26 DETT lobbed into a GTS-T (ie rear wheel drive) the thing had NO traction in 1st or 2nd and you had to back off in third to get traction. It was pulling around 450RWHP at the time, which is a big figure in anyones speak. Without a doubt one of the most impressive rides ive had in a skyline.

Jeremy

Steve... Those power figures on the Phoenix Power site are engine hp figures, not wheel hp.

that explains a bit, but I was just going off SKs post. still seams like a hell of alot of driveline loss. Also, SK talks of 330rwkw from 2530, so that means, from the same loss, 115kw loss for rw drive (330rwkw for 2530 vs 310rwkw for GTSS)

either way, I still think that SKs sceptical bone needs a recalibration:D:P

Hey guys, give me a break here, it was a hard Saturday night, alright?

OK, this is how I do the engine PS to rwkw calculation in a GTR.

579 ps X 0.9 = 521 bhp

521 hp / 1.34 = 388 kw

388 kw - 78 kw = 310 rwkw

Chris is right I use 60 'ish kw losses for (big gearbox and drive train) rear wheel drive Skylines (R33 and R34) and 50 'ish for (small gearbox and drive train) R32 GTST's. But this was an R34GTR so with them I have found it necessary to run the transfer case and centre diff and disconnect the drive shaft. So I added 8 kw to my usual losses on an R33 GTR in 2wd and 18 kw on an R32 GTR in 2wd. Experience tells me that a GTR looses about 85 kw in 4wd drive, so I don't think 78 kw is too far wrong.

So maybe my sceptical bone is out by a few kw's, Jack Daniels will do that to you. But I don't think it alters the argument.

As for HKS revising their max power outputs on GTRS's, well there are two answers to that one;

1. HKS are so dumb they published the figures first with out testing them properly. But the Pheonix car only made 579 ps (that's 290 ps each) which is a lot closer to the 310 ps rating than it is to 330 ps.

2. HKS want to sell more GTRS's

Either way, it makes my sceptical bone ache a little more.

Hey guys, give me a break here, it was a hard Saturday night, alright?

OK, this is how I do the engine PS to rwkw calculation in a GTR.

579 ps X 0.9 = 521 bhp

521 hp / 1.34 = 388 kw

388 kw - 78 kw = 310 rwkw

Steve is right I use 60 'ish kw losses for (big gearbox and drive train) rear wheel drive Skylines (R33 and R34) and 50 'ish for (small gearbox and drive train) R32 GTST's.  But this was an R34GTR so with them I have found it necessary to run the transfer case and centre diff and disconnect the drive shaft.  So I added 8 kw to my usual  losses on an R33 GTR in 2wd and 18 kw on an R32 GTR in 2wd.  Experience tells me that a GTR looses about 85 kw in 4wd drive, so I don't think 78 kw is too far wrong.

So maybe my sceptical bone is out by a few kw's, Jack Daniels will do that to you.  But I don't think it alters the argument.

As for HKS revising their max power outputs on GTRS's, well there are two answers to that one;

1. HKS are so dumb they published the figures first with out testing them properly.  But the Pheonix car only made 579 ps (that's 290 ps each) which is a lot closer to the 310 ps rating than it is to 330 ps.

2. HKS want to sell more GTRS's

Either way, it makes my sceptical bone ache a little more.

Hey guys, give me a break here, it was a hard Saturday night, alright?

OK, this is how I do the engine PS to rwkw calculation in a GTR.

579 ps X 0.9 = 521 bhp

521 hp / 1.34 = 388 kw

388 kw - 78 kw = 310 rwkw

Chris is right I use 60 'ish kw losses for (big gearbox and drive train) rear wheel drive Skylines (R33 and R34) and 50 'ish for (small gearbox and drive train) R32 GTST's. But this was an R34GTR so with them I have found it necessary to run the transfer case and centre diff and disconnect the drive shaft. So I added 8 kw to my usual losses on an R33 GTR in 2wd and 18 kw on an R32 GTR in 2wd. Experience tells me that a GTR looses about 85 kw in 4wd drive, so I don't think 78 kw is too far wrong.

So maybe my sceptical bone is out by a few kw's, Jack Daniels will do that to you.  But I don't think it alters the argument.

As for HKS revising their max power outputs on GTRS's, well there are two answers to that one;

1. HKS are so dumb they published the figures first with out testing them properly.  But the Pheonix car only made 579 ps (that's 290 ps each) which is a lot closer to the 310 ps rating than it is to 330 ps.

2. HKS want to sell more GTRS's

Either way, it makes my sceptical bone ache a little more.

1PS = .7355KW

1HP= .7457 KW

Also we are talking about GTSS's here, not GTRS's, must have been a good night in Sydney last night !

Cheers

Jeremy

Regardless of what some websites claim, I'm still pretty skeptical about the output of GT-SS turbos. Merli's car should be pushing them to their max flow, there's another R33 with them installed without internal mods (apart from cams). Will try to get a copy of a dyno sheet when it's available.

As to manufacturer quotes and idealised output ratings - can you tell me one manufacturer, distributor or turbo sales outlet who's turbos actually put out the power they claim? Even when used in a twin configuration the power is less than the sum of the two parts.

Oh, and I think we're pretty much splitting hairs on the whole GT-SS thing - until you see anything first hand I wouldn't believe it.

just my 2c,

we all know that on the HKS Japan website, they claim that the RB26DETT (with GT-SS turbos) makes 422kw (574ps) @ 7070rpm on 1.4kg/cm2, although has anyone noticed that the engine capacity of the RB26 has been increased to 2628cc over the standard 2568cc along with the 264/264 cams?

Also fyi, the wheel specs on the SR20DET GT-SS differ from the RB26DETT GT-SS where the SR20DET spec GT-SS has slightly larger wheels and an A/R .60 comp housing compared to the A/R .42 on the RB26 spec GT-SS.

http://www.hks-power.co.jp/products/turbo/...ss/ac_gtss.html

personally, i don't think the GT-SS (for the RB26) is rated at 320ps, i believe that it is a marketing thing and that it really is rated at the original 280ps.

again, this is just my 2c, so think of it what you will.

Yup :cheers:

Truth be told, I don't believe the new 320ps rating either... I think 280ps is more accurate, but I guess we'll see when my engine gets done.

With my engine build, I'll pretty much be able to push these turbos to their absolute limit, so we'll see what these babies can do! :):D

Elithrar: 200rwkw is reachable @ 15psi with the stock unit, pfc, fmic and zorst.

Merli: Have you considered 2510's. I have been for a ride in an R with them fitted and I must say lag was not evident at all. The vehicle was fitted with external wastegates in japan. Bit of a strange set up however the bottle neck up top may have been relieved some what with the higher flowing gates.

Boostd: nope, never considered them. For me, the choice was either the larger top end of the 2530s or the response of the GT-SS, and I went for the most responsive turbos I could find on paper, which were the GT-SS.

I also wanted to try something new and not follow the GT2530 bandwagon ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...