Jump to content
SAU Community

Trader Ratings

mike40sydney
 Share

Recommended Posts

  • 2 weeks later...
NewKleer Mentor

NewKleer

Posted
Posted

make a stand! before joining a group buy, check out the organisers trader ratings and see if theyve given more/same as theyve received (maybe that should be worded a bit differently...). at least that way you'll have an idea

some people simply dont know about it/dont remember, so it doesnt hurt to ask/give them a link to ur trader rating page

Link to comment
https://www.sau.com.au/forums/topic/142968-trader-ratings/#findComment-2691824
Share on other sites
  • 3 weeks later...
GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Seems a good enough place for my gripe Christian. I can't access any trader ratings including my own and can't leave feedback. I put Shan on the job a couple of months back but noy joy yet. This is the message:

Board Message

Sorry, an error occurred. If you are unsure on how to use a feature, or don't know why you got this error message, try looking through the help files for more information.

The error returned was:

Sorry, but you do not have permission to use this feature. If you are not logged in, you may do so using the form below if available.

Link to comment
https://www.sau.com.au/forums/topic/142968-trader-ratings/#findComment-2746649
Share on other sites
N1GTR Grand Master

N1GTR

Posted
Posted
Its a user access problem then, just so Admins know.

I can see it all as a SuperM. And i think other Mods can also, but that was a link to your own account so access driven that one is Geoff :)

I can see that link

And i can see the feedback he's now left for me :)

:)

Link to comment
https://www.sau.com.au/forums/topic/142968-trader-ratings/#findComment-2750741
Share on other sites
NewKleer Mentor

NewKleer

Posted
Posted (edited)

still waiting on feedback from 12 months ago for the consult interface :)

I would be easily over 1000 if this were the case :)

you mean easily over 150! (youve only given out a couple more than youve got). compare that to other top sellers who're lucky to have 50% of what they give, thats the real tradgedy of this story!

Edited by NewKleer
Link to comment
https://www.sau.com.au/forums/topic/142968-trader-ratings/#findComment-2750849
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Are you an oil nerd?

      By joshuaho96 · Posted

      You're not wrong but 5W30 at 100C is like 10 cSt vs 25 cSt for 10W60. If we think in terms of viscosity margin 10W60 will probably still be ok at 130C but 5W30 is probably too little. It's absolutely shocking how hot the oil gets in something like a stock FL5 from only ~3 minutes of use on the Nordschleife. I would not risk taking a car like that to anything remotely intense without a ton of work done for cooling. Heat shielding on the manifold/turbo/downpipe, oil coolers, etc. 
    • Kinkstaah
      Are you an oil nerd?

      By Kinkstaah · Posted

      I think the concept is highlighting the various scenarios where thicker oil helps, and thicker oil potentially doesn't help and only generates heat and costs power, in turn for safety which isn't actually any safer (unless you're going real hot). If anything this does highlight why throwing Castrol 10w-60 for your track days is always a solid, safe bet. 
    • GTSBoy
      Are you an oil nerd?

      By GTSBoy · Posted

      Jason should have shown a real viscosity vs temp chart. All the grades have very little viscosity difference at full operating temperature.
    • dbm7
      BCNR33 Blower Motor Resistor - Testing

      By dbm7 · Posted

      Oops... I meant to include the connector  view... BR/W - power from fuse L/W - motor negative to fan control amp (and off to HVAC pin19) OR/B - PWM signal (from HVAC pin20) B --  ground  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers.  Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel.  You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to).  This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job.  Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 
×
×
  • Create New...