Jump to content
SAU Community

Recommended Posts

Obviously you want something fully synthetic- I always use mobil 1, but hear that the top end Motul stuff (6100 or higher, like 300V?) is also very good.

People always complain that its too expensive when doing frequent oil changes, and that you can use cheaper oil because of the fact that its changed frequently (which does sound logical).

But its your engine, and the oil you put in it is all its got, why not give it the best :P

Also i suppose it depends how you drive it. If you redline it all the time, definitly go a good oil like the mobil. If you just cruise/potter it around i dont suppose it would really matter!

While on the topic of oil, can someone explain WHY turbo engines need synthetic oil!?

Cheers, NACHO

Yeah, I use Mobil 1.

I think synth oil can take the heat from the turbo better.

Also synth oil starts to break down at around 125-130 degrees, while the cheaper stuff breaks down at lower temps. That and the fact that the synth has better cold and hot lubricating properties.

J

Go Motul. I changed to 300V at the last change and it feels really good. 2000K and it is still like new, oil is still clear.

If you take the old oil down to the local servo (with mechanic of course, no point taking it to shell select!) and give them 5 bucks i'm sure they can get rid of it for you :)

Guest Oz Elitesport
Originally posted by Xeron

10w-60, u got a bad smoking or leak problem, cause if u dont get a lighter weight, check ur manual for what is recommended for ur areas temperature range, but ull be loosing a few horsies with that oil being so heavy when warm.

I'm using the castrol formula R (10W-60).

This has been recommended by others. Dont have a bad smoking or leaking problem, just took the advise of others.

Oz.

Castrol says this about their Formula R 10W-60 oil:

A full synthetic 10W-60 viscosity engine oil that ensures maximum protection under a wide range of driving conditions and high stress applications. It helps extend the life of your engine as well as minimise oil consumption. Originally developed for endurance sports car engines, it is recommended for highly stressed competition engines and older technology sports cars and luxury sedans.  

SAE 10W-60, API SL/CF, ACEA A3/B3

About the 5W-30 oil they say:

A synthetic 5W-30 viscosity engine oil which enables faster acceleration with excellent engine protection and performance. If offers excellent engine cold start responsiveness and contributes to increased fuel efficiency. Recommended for highly tuned, four cylinder engines and latest technology engines requiring 5W-30 or 10W-30 viscosity. Approved for use by Porsche, VW, Audi and Mercedes-Benz.

SAE 5W-30, API SL/CF, ACEA A3/B3/B4

And the 0W-40:

A full synthetic, free flowing 0W-40 viscosity engine oil that significantly reduces friction, whilst delivering more power, greater protection, reduced emissions and superior fuel efficiency. Recommended for the latest technology and prestige engines, such as Porsche, BMW, Rolls Royce, VW, Audi, Jaguar, Rover and Mercedes-Benz.

SAE 0W-40, API SL/CF, ACEA A3/B3/B4

I can't remember exactly, but I *think* the owner's manual specifies 10W-50 grade oil. That would make the 30 and 40 weight oils a tad too thin. I'll have to check the owner's manual when I get home.

All of these Castrol synthetic oils are of very good quality though so it may not matter too much. Either way, I'm presently using the 10W-60 stuff and I have absolutely no bad things to say about it. The car doesn't use a single drop between oil changes.

If you're changing oil regularly and often, it shouldn't really matter which brand you choose. Just get a good quality fully synthetic oil and you'll be ok. I personally chose Castrol over the Mobil because I like Larry Perkins better than Peter Brock :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...