Jump to content
SAU Community

Recommended Posts

front end of evo reminds you of a 34!? WTF...its great to see that the lancer is a completely different shape and does not look one bit like the older model, the subaru just looks like another wrx with a few cosmetic changes

EDIT: a side shot would be great

Edited by thorpe84

The EVO front looks like a Veilside kit gone wrong.... more wrong than they usually are... that's pretty wrong.

STI front looks good but the shape of the body makes it look like a CRX, very similar to a shopping trolley. I hope it's just the angle of the pic that makes it look like that.

After over 10 years of STi vs Evo, Subaru finally make the STi look better than the Evo...

... but that's if those concept pictures depict the production versions

wethjer they made it look better or mitsu made it look worse is debateable :S i rekon EVO X is ugly

The subi and mitsu look the same hey... same general lines...

And why put a 6cyl in them to whoever said that? Look at it this way, if you had a size 6 foot, you wouldnt buy size 4 shoes. THEY DONT BLOODY FIT!!!

so you reckon the 6pot boxer doesnt fit a rex? :no:

No I know they do. As I have seen it, with all the gear etc. But in terms of what its going to do to the rest of the cars handeling and dynamics, and factory fitting it...

And as old mate was revering to both, I cant see mitsu fitting a 6cyl that is BETTER than what they have now in the evo.

That and they are marketed as 4 bangers. Thats the market they are in. You put a 6 in either and it puts it in a different market.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...