Jump to content
SAU Community

Recommended Posts

30 inch tacho with 60 watt shift light.

seriously, an accurate boost gauge. the rest are all sufficient for street use. unless you're going track, then go for all the pressure and temp gauges you can.

Rice-o-meter

Are you getting too close to a car with a neon kit that might blind you OR a car with too many/large pointy wings that could have your eye out.

Bulldust-o-meter

is great for those conversations through the drivers window at the lights or carparks when people are telling you whats under the bonnet.

Hotchick-o-meter

is also popular for those young lads looking to do bog laps.

Ovulator....she is on heat gauge.With pointer to location of female. :P

Busted......cops up a head gauge.With pointer to location of police. ;)

Flying-high......avoid drug dealers gauge.With pointer to location of drug-dealer :D

Is it time to close this thread yet??????

Thats not a bad combination.

I'd probably trade boost for oil temperature.

Oil temp guage will be a souvenir from TAC :huh:

"Maybe you guys are forgetting the fact that he said its a GTT... Since the stock dash already has oil pressure ...."

Stock guages on a car that is street driven far from equipment limits are fine but...see below

wouldnt it be better to change the guages or add more relevant ones if the car has been modified heaps

absolutely, a well know Perth tuner reminded me a while a go that the stock guages on my 32R were "slow to react" and as i've got a few bucks sunk into my car I thought it would be wise to get an appropriate level of monitoring on board...rice-o-meter LOL

boost guage

- you'll be able to tell if your car is over boosting, and be able to slow down if it goes to high. important for modified cars!

oil pressure and oil temp

- to avoid serious damage to the engine and diagnose any faults before they become a serious threat

water temp (cooling)

- avoid any head gasket failure or cooking your enging (same as above really)

fuel pressure

- if you start loosing fuel you can end up setting fire to your car if you don't notice your fuel trail, which is why it is important to have a guage. you can always rely on your sense of smell to help you out, but sometimes the heat of the moment gets too much (excuse the pun) and 'dirty imports' have a fuel smell to them anyway

I know there are 6 there but it depends on how 'safe' you want to be. are you planning to mount them on the pillar or below the stereo? if both, mount the top 3 on the pillar, and the remaining more descreatly under the stereo.

you could just get a motec dash though...

Interesting thread. Im not in it for the rice factor. More knowing the status of the car and give warning signs when things may be going wrong.

How hard are these gauges (oil pres/temp, water, fuel pres) to install yourself, and is there much room for error (ie installing it reading the wrong figures)?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...