Jump to content
SAU Community

Recommended Posts

  • 8 months later...
  • Replies 93
  • Created
  • Last Reply

Top Posters In This Topic

Why does everyone want gay stainless steel manifolds that crack etc heat fatigue, 6 boost manifolds and ones made from steel are 10 times better in theyr can b heated and cooled alot more times without damage plus they have been found to retain more heat and decrese spool up times of liek 2-5% percent from memory because they retain more heat the exhaust gas flow is quicker theirfore making the turbo spool faster, the only downside in weight thats all but if ur actually going to drive ur car ie do afew km's in it wouldnt u want something that is going to last....

Thanks Rory

note a link for some 6 boost manifolds:

http://www.horsepowerinabox.com/HPIAB2/category15_1.htm

i want a 6boost one but there is a bloody 4-6 week wait on them. i need my car back now as its my daily driver and its in peices as my stocker is cracked...

i have been told that the stocker will only crack due to running to lean....??? any comments?

I have recently had my 6boost (SR20) ex manifold and stock SR20 inlet manifold honed by Andrew Sanders (along with my turbo compressor cover). I don't have the before/after flow results on me but will post up later for anyone interested in this process.

OK for what its worth 6Boost ex manifold and standard blacktop inlet manifold (SR20) before and after extrude honing at 28 inches. Please note that my mandate to Andrew Sanders re exhaust manifold was not to equalise flow as I didn't want to increase the volume too much in runners 2 & 3 and loose any response. And my mandate re the inlet manifold was to equalise flow - which is nearly perfect. Just an example of the benefits of extrude honing.

6 Boost Exhaust Manifold

Before.............After

1 250............260

2 220............245

3 222............247

4 252............262

Standard SR 20 Blacktop Inlet Manifold

Before.............After

1 254............300

2 257............306

3 270............306

4 254............300

For comparison sake I pasted this RB exhaust manifold flow data previously posted in this thread but Im not sure at what pressure the flow tests were done?

Some flow rates for you guy's from extrusion flow honing standard manifold ,hks cast iron manifold and hks cast iron flow honed

standard manifold .........hks cast ...............hks cast flow honed

1 159.7.........................170.7............................194.8

2 162.4.........................166.6............................203.4

3 160.7.........................178.7............................198.7

4 150.1.........................183.6............................200.3

5 149.9.........................182.2............................207.8

6 173.3.........................184.7............................202.8

^^^^^ agreed but IMO the 6Boost manifolds has one of the best collectors in the business. Mercury Motorsport made 562 rwhp from their stock stroke sr20 with a 6 boost mani and GT35 turbo. This car also ran 10 sec quarters with manual box.

My manifold is also unique in that it has been custom made to suit one of the new round collector v-band Tial cast stainless housings for my HKS GTRS turbo.

Edited by juggernaut1
i want a 6boost one but there is a bloody 4-6 week wait on them. i need my car back now as its my daily driver and its in peices as my stocker is cracked...

i have been told that the stocker will only crack due to running to lean....??? any comments?

Suggest you get in touch with Leigh from Extreme Turbo Manifolds if you need something sooner. The link is in my sig.

Found this link on power porting process of before and after hp figures done on a test mule RB30 engine when Specialised Power Porting was in its infancy.

http://autospeed.com/cms/A_0622/printArticle.html

  • 1 year later...

a bit of a update on a old topic but...... i just spoke to Abrasive Flow Engineering who does or did work for uas on hone and extrude and his exact words are for a rb25det manifold.

"""don't wast your time and money they don't flow as good as a hks manifold ""

and

"""for $900 to extrude and hone i would go and get some thing better"""

f#%$ me.this is from the guy who does them while some companies are begin for work due the the $$$$ crises this guy has shocked the sh#@ out of me so ..........after reading this post and many like it over the years and looking at the figures people have posted on flow have we all been grossly mislead by people in the industry have figures been made up for the trusting customer.

what is one to thing !!!!!!!

if anyone does reply do it here.: http://www.skylinesaustralia.com/forums/Ex...47#entry4450747

Edited by WARLORD

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...