Jump to content
SAU Community

Recommended Posts

Items:

V35 sedan standard front bar

V35 sedan aftermarket side skirts and rear bar

V35 sedan HID right headlight

19" or 20" rims+tyres in 5x114.3

twin 3" tip exhaust x2

Extra Info:

preferbly in factory pearl white

not too fussed on offset. dont really mind chromies as I'm just going for a show pony look

Need full headlight including ballast module and globes

Contact Details:

pm on this site

Price and price conditions:

i can get a full kit for around 1k, so cheaper than that if possible

headlight not sure, i bought after market set for $300, i understand these are HID though

no more than 1k, found a set for $600, but wanna see what other people might have

Hey guys I'm looking for a rb20 wastegate actuator for my rb25.

Correct me if I'm wrong but the rb20 actuator runs constant 10psi compared to constant 8 psi with rb25 actuator when you ground solenoid.

Thanks

Edited by Vlasi

NEED the following for an r32 gtst:

Drivers 1/4 panel - black preferred, in exc. cond.

drivers door - again black, same as above.

Would like the following :

std exhaust to get through regency

r32 gtst std diff

rb20 engine mounts - the metal brackets, not the rubber mounts

r32 gtst headlights in good nick

Let me know how much etc,

cheers.

BTW, if you have parts (like a diff) id prefer if it was ready to go, not "ill pull it out next week" which never seems to come.

Edited by Bl4cK32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...