Jump to content
SAU Community

Recommended Posts

A straight through pipe doesn't really make it that much louder now drone in the cabin (unless the exhaust is prone to do so anyway) just a tad deeper and gruntier sounding.

A well setup exhaust shouldn't drone in the cabin full stop.

A straight through pipe doesn't really make it that much louder now drone in the cabin (unless the exhaust is prone to do so anyway) just a tad deeper and gruntier sounding.

A well setup exhaust shouldn't drone in the cabin full stop.

agreed...my exhuast is pretty much a straight pipe from the cat back and it IS loud...but not drony and more than bearable on idle and low revs.

How about you just do the right thing and buy a new cat...

Think of the environment.

Think of the cancer growing in your lungs from breathing in your un-catalysed exhaust gasses.

Is it worth it all just for gaining a few kW?

those kind of emmissions won't cause lung cancer... not in short-term exposure anyway

lung disease, yes (eg lung fibrosis)

you'd have to be breathing in funes everyday for years to be at risk there

honestly, i did this to my car before i got a high-flow cat and i noticed no increase in exhaust note, and no difference in power at all!

so it begs the question, why bother?

A straight through pipe doesn't really make it that much louder now drone in the cabin (unless the exhaust is prone to do so anyway) just a tad deeper and gruntier sounding.

A well setup exhaust shouldn't drone in the cabin full stop.

mine mustn't be setup too well then. hehe!

Going back to the original question why would you go to all the effort of putting a straight pipe through the cat? its pointless, if a cop pulls you over its usually due to the smell or noise and then they'll send you to the transport department. There are performance gains from a straight through pipe, but its not worth it on your daily driver.

My car has a decent high flow cat but since i installed a power fc and had it tuned it is running quiet rich and i always get pops through my exhaust, sometimes very loud ones. will this destroy my cat pretty quickly?

yeh they might look like a cat but if ya blowing flames out the exhaust they might be a bit suss about that

ive have a stock r32 im running on the track. ive gutted the cat and taken the rear muffler off. will i blow flames?? if so, cool!!!

and will i notice much difference without it? i havent tried it yet, have to wait till next weekend.

i will have a 3'' system on it by feb next year but for now its honkin ok.

Edited by johnGTS-t

there is almost no difference between a 'highflow' cat and a straight through pipe in terms of performance...

I know because the 2 bolts holding my cat to the front pipe came out last week and I was driving around for a few days with no muffling of any kind... the noise was deafening and sounded like crap below 3000rpm... I was even turning the ignition off at light because I was so ashamed...

now its fixed the performance difference is hardly noticable and that is with a cat, resonator and muffler bolted back on... so just get a proper cat and do everyone a favour

kinda sounds like you were going to gut your cat no matter what these guys have said? :S

the gutted cats iv heard sound hollow n a bad sound as if they have big exhuast leaks...

CJ

ps, i must be a lazy cu*t, i sit in maccas drivethrough for 1hr!! (yeh right)

Ive got a black car so it won't look that different. It will fit you just have to cut the cat housing a bit. As for cancer and contributing to the death of the environment.. you guys are funny.

I think it evens out for me acually, i ride to work and catch the train to uni so i only drive my rig on the weekends which is alot better for the environment. The lazy cu*ts who drive everywhere and would rather sit for 1hr in macas drive through than walk into the place and be in and out in 5 mins are the ones you guys should be angry at.

cheers.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...