Jump to content
SAU Community

Recommended Posts

hey there guys i am a bit concern that my hand brake is not locking the wheels up. when car has stoped the hand brake still stops my car from moving its just when i pull it up when moving they dont lock. i do clutch in and i have adjusted them too.

i probally havnt adjusted them right but yeah, any help will be great

thanks

Link to comment
https://www.sau.com.au/forums/topic/144332-hand-brake-not-locking/
Share on other sites

Have you checked the handbrake shoes?

Proper way to adjust handbrake is to back it right off at the lever, then tighten it all the way at the drums so it doesn't move, and then back it off 4-5 clicks. Then tighten the lever up till it locks after 5-6 clicks.

hehe my questions r for the benefit of myself and the other stupid ppl to scared to ask :O

any question you ask is stupid justin, hehehe.

the handbrake mechanism is in behind the rear rotors. you pull the rotors off to expose them.

you said you only wanted a pic of the drums shoes :(, anyway heres the Translated version. if there is still plently of meat left on the drum shoes but they have a glazed surface just do what Snowman said. if they are on the skinny side of things replace them, on that note anyone know where to get drum shoes and what price they are?

you said you only wanted a pic of the drums shoes :rofl:, anyway heres the Translated version. if there is still plently of meat left on the drum shoes but they have a glazed surface just do what Snowman said. if they are on the skinny side of things replace them, on that note anyone know where to get drum shoes and what price they are?

from the page:

"You do not know why is, but R31 (the Indian ram system) the emergency brake works like the ogre"

hahahahahahahah!!!! :laugh:

URAS make an awesome upgraded handbrake shoe for Skylines - if you plan on doing a fair bit of handbrake stuff for either drifting or motokhana's/autocross. I use them and they make a big difference over the standard shoes.

brake%20drum.jpg

http://www.uras.com.au/

For stock ones you are probably better off at a wreckers. From what I gather it's one size fits all for skylines.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...