Jump to content
SAU Community

Recommended Posts

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Hi guys

We ran a drift training day earlier this year, and are trying to do something similar next year. So stay tuned.

There are a number of groups who offer open drift 'practice' days too.

For general info - check out:

http://www.driftaustralia.com.au/

http://www.driftzone.com/

http://www.vicdrift.com/

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2706307
Share on other sites

There are practise days like the one on Wednesday this week that will be at Calder.

They have a section.

Its a bit hard to learn there because there is limited time and space.

You will find that most People who do so Have learnt on the street, which is very unsafe and not worth it.

Think about drifting before you get into it, do you want to do it full on, or you just want to give it a shot. If you just wanna give it a shot I reccomend its not worth it.

An incorrectly setup car can make it very hard and very very dangerous to drift, drifting is an expensive sport and it certainly makes it hard on the track if you dont have a well setup car. Lots of people can claim to drift, but going sideways is not the same as properly drifting like high speed entrys, clipping points, weight transfer etc.

If your passionate about it go for it!!! Ill be there at Calder this Wednesday and Winton next month.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2706385
Share on other sites

Go put the hardest smallest width and profile tyres you can fit on the rear of your car and go have some fun. I've done it a few times and I think you'll find most of the people knocking it have never tried it or can't do it. The first time was fun on hard tyres but with the second time there with sem'i the car gripped to much after the first run.

Circuit is more fun for me but as you say you just want to learn car control drift is slower and therefore your less likely to hit something.

Go give it a go. If you just want to go for a thrash Calder isn't to bad. Apart from a few guys everybody there are just hacks.

Just don't drift under the bridge. Good luck with it.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707324
Share on other sites

Yeah it seems to be the "cool" thing to pay out nissansilvia.. god knows why cause the interests of both are really very similiar.. Regarding drift there _are_ a lot of VERY experience drifters on NS.com but it's not a place for learning where to drift :S. Prolly best off going to a skid pan day (Which I know NS organise frequently in victoria) if you're brave you can take ya car to calder too :happy:.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707376
Share on other sites

Actually going the smallest width and profile tyres is incredibly dangerous for a learning or experienced drifters.

Every Day, yes day, we see guys crash due to running skinny tyres on stock rims. You need grip to drift and small tyres dont provide that.

Lots of you bag out NS.com for no reason. You guys like race days and DECAS and they love drifting.

Funny most of the guys that do bag out NS have never been on the track. They think just because they did a DECA that they are track veterans because they are affiliated with SAU. When many NS members have attended both Calder and Winton and many skidpan days.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707487
Share on other sites

lol the amount of retards on ns.com that go drifting in their owns streets is incredible...

almost every silvia owner thinks they are in the d1 everytime they go out onto the streets, im sure everyone see's that.

vicdrift is there for a reason, albeit expensive, its still there for this sort of thing to take place

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707523
Share on other sites

You are really misinformed and have made a huge generalisation.

I hardly ever see many silvias drifting on the street. Most of them are well behaved and drive properly.

On the other hand, every time I see a R32 or R33 they drive like total tools at double the speed limit and try showing off. Every time no doubts about it. In traffic where theres danger to others.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707726
Share on other sites

now you are both making generalisations. the biggest factor that differentiates the two sites is age. and that is simply because of the cost factor. generally speaking tha people's cars on ns are cheaper than those here.

Dont get me wrong, there are some big expensive cars there but they are far and few between.

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707761
Share on other sites

You are really misinformed and have made a huge generalisation.

I hardly ever see many silvias drifting on the street. Most of them are well behaved and drive properly.

On the other hand, every time I see a R32 or R33 they drive like total tools at double the speed limit and try showing off. Every time no doubts about it. In traffic where theres danger to others.

yer bro im alwayz dosin down mah street in mah R32 dawg! itz lyk hektic when i rip da skidz past da popo n past da sk00l crossin wid kidz n shit y0!

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707783
Share on other sites

Could you explain to me Starionturbo how drifting with tyres that have little grip at slow speeds causes you to crash. Are you sure the drivers aren't try hard kids in thier auto's N/A's in industrial estates. I know there are a lot of them out there. I've met a lot of them selling parts.

From all of my driving experience it is a lot easier to get a car sideways at low speeds and hold it with hard smaller tyres and low profile.

Are you saying that you could drift better with 275mm wide semi comps compared to stretched 195mm wide hard old tyres in a r33 pressumably stockish r33.

Also if you need good rubber why do the drifters stretch 235mm tyres over 10inch rims and why do they sit the tyres on the roofs of buildings to let the go hard?

Only the good guys use good tyres with grip in high powered cars. Not learners! Good tyres snap back on decelleration to harsly for a learner.

It just seems that most drifters are talkers and seem to think thier D1 drivers.

We have some really good genuinely capable drifters in our club and this is only my opinion of other people I've met.

Your thoughts please....

Link to comment
https://www.sau.com.au/forums/topic/144927-drifting/#findComment-2707866
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...