Jump to content
SAU Community

Recommended Posts

Hey guys,

I got a broken stud on the exhaust manifold on number 6. I'm dying from the gases and lack of fuel economy. The car is hating sounding like a tracker and losing power.

Now the question is...Can I drill the stud out and helicoil it with the motor still in the car? Will I have enough room as its on #6?

Thanks.

(l20et in hr30 by the way)

Hey guys,

I got a broken stud on the exhaust manifold on number 6. I'm dying from the gases and lack of fuel economy. The car is hating sounding like a tracker and losing power.

Now the question is...Can I drill the stud out and helicoil it with the motor still in the car? Will I have enough room as its on #6?

Thanks.

(l20et in hr30 by the way)

This has gotta be the most useless forum!! Ive already a dozen replies on sdu and hybridz....

easiest way is try and track down a stud remover guy to do it for you unless you have an air compressor right angle drill drill bits and also easy outs/stud removers be able to do it yourself why not pull off manifold and everything around it and have a look you will find you may break more studs as well as you do it but hey atleast youll be able to replace them easier as well, good luck

This has gotta be the most useless forum!! Ive already a dozen replies on sdu and hybridz....

Have you ever thought it's you George????

You ask some of the most stupid questions. Maybe, just maybe nobody has broken the manifold stud at #6 here in Oz, because I sure haven't in all the years I have been playing with these cars.

I would think common sense would tell you, maybe a good look under the bonnet might give you the most probable answer to your question.

As for useless, I think that's a bit harsh, because you forget, HybridZ is an L6 series specialist forum, where SAU and L6 engine specialists would be very short on the ground. I know if I want to know anything specific about L6 engines, I don't ask them on SAU, I go direct to the best source HybridZ.

The L6 engine is growing less and less popular and only the diehard purists want to stay with them.

Did you ever think to ask NDSOC Forum the question? bet you didn't?? but you can criticise SAU without reservation.

Cheers, D

Have you ever thought it's you George????

You ask some of the most stupid questions. Maybe, just maybe nobody has broken the manifold stud at #6 here in Oz, because I sure haven't in all the years I have been playing with these cars.

I would think common sense would tell you, maybe a good look under the bonnet might give you the most probable answer to your question.

As for useless, I think that's a bit harsh, because you forget, HybridZ is an L6 series specialist forum, where SAU and L6 engine specialists would be very short on the ground. I know if I want to know anything specific about L6 engines, I don't ask them on SAU, I go direct to the best source HybridZ.

The L6 engine is growing less and less popular and only the diehard purists want to stay with them.

Did you ever think to ask NDSOC Forum the question? bet you didn't?? but you can criticise SAU without reservation.

Cheers, D

screw you buddy, it was like taht when i bought it.

harsh? harsh is the least of it.

SDU was more helpfull.

what other questions were dumb? maybe i want advice...

Edited by george.bryant
  • 2 weeks later...

i had a similar pro b with my l20et when i got it all i did was used my tig to build up the stud untill i ca just wind it out with a set of multigrips.

i have also used the mig to do the same but its a little harder you have to make sure you get peno with the first bead.

if you dont have a welder a easy out is your best bet but its a bugger of a job... good luck.

i had a similar pro b with my l20et when i got it all i did was used my tig to build up the stud untill i ca just wind it out with a set of multigrips.

i have also used the mig to do the same but its a little harder you have to make sure you get peno with the first bead.

if you dont have a welder a easy out is your best bet but its a bugger of a job... good luck.

Thanks for you help guys.

Got it all sorted out and she doesnt tick now (not from the leaky manifold at least)

Thanks for you help guys.

Got it all sorted out and she doesnt tick now (not from the leaky manifold at least)

Why dont you let on how you fixed it. Thats what this forum is for. :laugh::laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 馃槩 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
    • meh, it was a good video, clear about the issue and how he dealt with it. A bit heavy on the RTV and very brave to put an RB in anything without rebuilding it first, but otherwise I thought it was good Dose, I'm not sure that having the pickup forward is a big issue; yes of course the oil could shift under brakes but the sump should never be empty enough for that to be a problem (unless you also have a higher volume oil pump, and that oil can't return from the head to the sump quickly enough)
  • Create New...