Jump to content
SAU Community

Recommended Posts

Hard luck dude the odds caught up.

May i ask whats wrong with your exhaust and wheels setup?? Or why they defected?

They're 18" and stock are 16" so i'm right, but i need engineer certificates saying that they comply with the australia design rule.

same with exhuast... any modified exhaust on a car has this rule

Yeah really, it'll cost you more grief than its worth. Lesson learned

definitely

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Dude ouch!!

As said, yes it could of been a lot worse.

Sucks though majorly that you got done though; for both speeding and defects.

What a shit way to start Christmas

I had the same treatment not long ago... sent to epa for noise... had to whack a stocker pee shooter on there to pass... and the dicks defected me for an unenclosed pod filter.... and ride height..

but i out smarted them with the ride height ... i just put tighter rubber things on to support my exhaust and it raised it like 30 mm .. lool

They're 18" and stock are 16" so i'm right, but i need engineer certificates saying that they comply with the australia design rule.

same with exhuast... any modified exhaust on a car has this rule

definitely

Hey,

no, don't think so. Pretty sure exhausts are an 'owner-approvable' modification according to the RTA.

This means that as long as it passes the relevant ADRs (ADR28, for noise level; ADR37, for actual

gas and particulates; there may be others - ask the RTA) it's OK. It doesn't need to be standard.

What most likely happened is that they tested your car with a dB meter; and it was too loud (corrected

reading of over 90dB, putting the car in violation of ADR28). I doubt they tested ADR37 - pretty sure

the kit to do that test only exists at Penrith and Botany.

To fix this, visit an exhaust shop with a meter and tell them you need it quieter than 90dB at test RPM -

for you, it's probably around 3500RPM. Note I said 'corrected' - they're supposed to apply corrections

for temperature and pressure (this doesn't often happen). If you get tested in the middle of a cold night

your car will read louder than in the middle of a hot day.

Borrow a set of stock rims.

Then visit the inspection station, show them your car complies with the paperwork, and get the

defects cleared. Visit them in the middle of a hot day in case they don't apply the corrections on the

noise test.

Then your car is street-legal again, and you can figure out whether you want to get your car

engineered (budget about $500) for the rims or not. If the rims stick out beyond the bodywork I'd

guess you have SFA chance of getting them approved - talk to your engineer about that (you might

be able to flare the guards enough to get them allowed). Might be better to replace them with a set of

smaller rims which don't require approval from a signatory.

Lastly, don't drive like a tool. Driving like a tool attracts the wrong sort of attention. And if you _do_

drive like a tool, don't be surprised when the police throw the book at you.

Regards,

Saliya

Hey,

no, don't think so. Pretty sure exhausts are an 'owner-approvable' modification according to the RTA.

This means that as long as it passes the relevant ADRs (ADR28, for noise level; ADR37, for actual

gas and particulates; there may be others - ask the RTA) it's OK. It doesn't need to be standard.

What most likely happened is that they tested your car with a dB meter; and it was too loud (corrected

reading of over 90dB, putting the car in violation of ADR28). I doubt they tested ADR37 - pretty sure

the kit to do that test only exists at Penrith and Botany.

To fix this, visit an exhaust shop with a meter and tell them you need it quieter than 90dB at test RPM -

for you, it's probably around 3500RPM. Note I said 'corrected' - they're supposed to apply corrections

for temperature and pressure (this doesn't often happen). If you get tested in the middle of a cold night

your car will read louder than in the middle of a hot day.

Borrow a set of stock rims.

Then visit the inspection station, show them your car complies with the paperwork, and get the

defects cleared. Visit them in the middle of a hot day in case they don't apply the corrections on the

noise test.

Then your car is street-legal again, and you can figure out whether you want to get your car

engineered (budget about $500) for the rims or not. If the rims stick out beyond the bodywork I'd

guess you have SFA chance of getting them approved - talk to your engineer about that (you might

be able to flare the guards enough to get them allowed). Might be better to replace them with a set of

smaller rims which don't require approval from a signatory.

Lastly, don't drive like a tool. Driving like a tool attracts the wrong sort of attention. And if you _do_

drive like a tool, don't be surprised when the police throw the book at you.

Regards,

Saliya

Wow, thanks for that.. I can tell you now that my exhaust has been already defected and taken to an exhaust shop which complies and is under the 90db rating. RTA did NOT use any sort of meter for the exhaust as the car was off, For the rims, i'm putting stock back on and getting cleared..

Thanks for all your help.!

bad luck matey, the defect doesnt look too bad though couldve been heaps worse. shouldnt be too difficult to get it cleared

if the cop really wanted to be a c**t he wouldnt of let you chuck a shit lol.

good luck with the defect clearing.. looking at the bright side, at least with the 3 months you have off you'll save alot of money not driving and modding :)

Just a quick note, you won't lose your license for ages yet. I know someone who was booked for the same offence in January of this year. He paid the fine on time and received the letter from the RTA a good few weeks later advising that his loss of licence was to occur in the first week of May through to July.

that defect notice they gave you specifies that to be cleared you need to get a minor part inspection at an AUVIS.

This means that you only need to get it inspected at any place that can provide a blue slip.

Put the parts that were mentioned on the notice back to standard, then get it inspected. You may not even have to change the exhaust, talk to the place you are going to get it passed by and see what they say needs to be changed before doing anything.

Either way, you don't need to take it for a full RTA inspection and emissions test, so dont stress about it, it is not big deal.

You will probably still have your license for a while yet, so get it done now while you can drive.

Sorry to see you got caught out!

Edited by siksII
wow intresting...

D_I_F i had mcdonalds.. i have no idea how i got sick..

Sorry dude but I suffer from the same problems.. if I eat something wrong it def wont agree with me.. so I stop eating those kinda foods.. Sloves the problem all together..

Not to mention you just got your licence and should know better..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...