Jump to content
SAU Community

Recommended Posts

Yer but doing it that way u still pay 17k for the car itself, then add

3" stainless steel turbo back exhaust - $650

600x300x75 FMIC -$450

Apexi Power FC $800

Apexi Commander $350

Apexi EBC $450

K&N pod filter in stainless steel cold air box $150

Bosch 040 fuel pump (in tank and quiet) $200

Larger radiator (34mm thick v factory 25mm thick) -fark knows $400

Stainless steel radiator guide $100

Strut braces front and rear $150

Autometer boost and oil temp on A pillar $200

AVS model 6 17x8 front and 17x9 rear $1k

Water pump, radiator, timing belt, idler and tensioner bearings replaced at 85,000 kms $600

Thats like 5.5k hes saved right there and he can continue upgrading the car from where its at...

how about I spend my own cash, do stuff my own way like you all did, and not tell other people what to spend their money on because I think its the best way. If i spend my own cash, I know what ive done and how its been done. If i buy it already done, i dont know whats been done, how its been done and if its reliable or not. Not every car is tuned to an A1 grade (althought i trust boostworx simply because 5 other mates have).

I buy my car stock, I do it up myself so I can appreciate what its become. Thats what its all about, not just the driving experience. I'm sure Adz here didnt just buy the car to leave it that way, hell want to upgrade it, replace parts with better ones, etc.

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Everyones "stuff" is the same basic setup which he has bought.

Doesnt matter if u do it now or later a pfc plugs in, and intercooler bolts in the same spot, a fuel pump goes in the same spot...

All of these parts are the same for any skyline, whether u do it yourself or someone else has has. Buying parts individually is more cost effective. The usual "its worth more as parts than as a whole comes in to play".

U do what u want....its your money after all :wub:

Its pretty hard to get a car 100% spot on by just a dyno tune.

Often than not it will ping under certain conditions, take note of those conditions/rpm/load etc and take it back for a touch up.

or.. just touch it up your self.

what would the next logical upgrade be?

ive always wanted a carbon fibre bonnet so i think that will be what i do first

Carbon fibre bonnets are defectable. Not worth the hassle and $$ of having to return the car back to stock.

Grab a set of injectors and either a GCG highflow for ~250rwkw or a GT30 .82 internal gate (requires new dump pipe and some intake mods, but it still can be made to look stock) for 300rwkw odd.

If you go the GT30 route you may want to seriously consider ripping the head off and throwing a thicker head gasket on it to drop the comp, those cast pistons are fragile, all though in a perfect world with a good tune and perfect consistent fuel it will be 100%.

Its up to him as to how he wants to modify the car - and using the forums he can figure out what he wants to do next. But the only thing I will say is - its not enough just making power, to do well on the roads and/or track, handling and all that should be looked at as well

Well???? You picked up last night yeh?? How was it??

yep last night was the night..... it was ummm..... hmmm.... f**cking incredable! so so happy wid it!! The best part about it is you can drive it like a little old lady and its comfortable as but then when you want to go fast jus hit the right pedal and its a rocket! couldnt be happier wid it!! best thing ive ever done!!

Yer but doing it that way u still pay 17k for the car itself, then add

3" stainless steel turbo back exhaust - $650

600x300x75 FMIC -$450

Apexi Power FC $800

Apexi Commander $350

Apexi EBC $450

K&N pod filter in stainless steel cold air box $150

Bosch 040 fuel pump (in tank and quiet) $200

Larger radiator (34mm thick v factory 25mm thick) -fark knows $400

Stainless steel radiator guide $100

Strut braces front and rear $150

Autometer boost and oil temp on A pillar $200

AVS model 6 17x8 front and 17x9 rear $1k

Water pump, radiator, timing belt, idler and tensioner bearings replaced at 85,000 kms $600

Thats like 5.5k hes saved right there and he can continue upgrading the car from where its at...

Cost more than that and i fitted EVERYTHING myself. Only thing i didnt do was tune PFC.

Gonna miss it. Glad its going to a good home. Just as well i have a GTR otherwise i would be serioulsy depressed.

If i had kept it i would have done whiteline shocks/swaybars, injectors, and 2535 or GT30.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...