Jump to content
SAU Community

Recommended Posts

hey all my car is running like crap and i dont know y it runs worse on a cold night than a hot day its running stock boost 6 or 7 psi flat. the other night i put my foot to the floor and it sounded like it was boosting but it wasnt going anywhere felt like it lost all its power it still revs up to the limiter but if i back off to about 1/4 throttle it just takes off and goes great and i have no idea y i have the usual mods FMIC (gktech) pod filter turbo back zorst and a gutted cat any help would be great thanks

Link to comment
https://www.sau.com.au/forums/topic/146077-help-needed-cars-running-like-crap/
Share on other sites

yeah iv got boost gauge thats y i know its always at 6 psi it never goes over it and i checked my plugs they look like there ngk iridium gapped to .8 there so i dont think its them i have no idea what it could be i dont see y it would go into r+r mode with stock boost

its a greddy boost guage and its sits just under .5 bar so 6 or 7 psi y do u think there is something wrong there i thought that was about how many psi they mad standard and y do u think its going into r+r then what do u think would be causing it

hey there,

This explains perfectly what my car does sometimes.

I've changed coil packs and afm to no avail.

Could it be o2 sensor?

I can't seem to find any more info on this - i tried searching but didnt get very far.

any help would be great, thanks

bobby.

hey there,

This explains perfectly what my car does sometimes.

I've changed coil packs and afm to no avail.

Could it be o2 sensor?

I can't seem to find any more info on this - i tried searching but didnt get very far.

any help would be great, thanks

bobby.

:wave:

If you search with:

+rich +retard

you'll come up with a million threads

I had a very similar problem to yours, it was an air leak, check all your hoses!

i had a tiny crack in one of my rubber hoses (10cm hose and it was not hitting full boost at all even when i floored it, replaced it with a new hose and worked perfectly, boost was just as it had been before! try that...

hey there

lol im not sure about o2 sensors or the wastegate actuator but what i've experienced and stuff i'd jus say...

go ebay ... or ask sau ppl

... n get a used ecu for your car..perhaps 50 bucks?

or ask your mates to lend you one,n if your car works better then it was the ecu, if not forward on to mechanical parts but dun waste ur time on rich n retard its a bitch to deal with it...

  • 1 year later...

Hey all,

In my case this problem was solved by taking apart my ECU, and resoldering all the joints for the connectors to the loom. This isn't a job for the amateur, you are dealing with a very sensitive precision device here...

In my opinion, the manufacturer was fairly stingy on the amount of solder used for these important connectors and they are susceptible to cracking thus causing bad or intermittent connections, or altering the amount of resistance measured in the case of sensors.

Since doing this a few months ago, my car has not repeated this annoying 'rich+retard' mode.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...