Jump to content
SAU Community

Recommended Posts

i just put on 400r rear bar on my car

and noticed there is a bit of a gap between the body (under lights and skyline logo panel) and the top of the boykit

i put the stock bar back on and there isnt as much as the 400r bar

anyone got any pics of there 400r bars or have noticed this

any help will be great

also with this bar the rego plates dont fit

wat u guys do to get it to fit besides bending them

Link to comment
https://www.sau.com.au/forums/topic/14648-who-has-a-400r-rear-bar-on-there-r33/
Share on other sites

yes i have a 400R front bar on mine. i also noticed the gap is slightly bigger between the bar and the head lights , but no one else has noticed yet.

you dont have to bend or cut your plates just use the middle holes of the plate and put in washers or some sort of spacer between the plate and the bar.

Originally posted by hippy

correct me if i'm wrong but there is no such thing as an oem 400r kit for a gtst??

100% correct.

The 400r was a 99 car limited edition 33 GT-R w/ stroked 2.8 litre 400hp motor. Nismo never licensed this kit.

By definition they are all copies (but so what, it's a coolio kit!).

T.

no its not cyal8r.

guess again.

i recon the bar is too dam low. i wish i had of got a 2 piece one so i could take the bottom piece off. to late now but.

i have 18s on the car but it may seem high cause i havent lowered it yet. still stock suspension.

Originally posted by walkoau

i recon the bar is too dam low. i wish i had of got a 2 piece one so i could take the bottom piece off. to late now but.

i have 18s on the car but it may seem high cause i havent lowered it yet. still stock suspension.

I think most of you have seen this:

http://www.nitroware.net/~tony/r33_front.jpg

One piece bar. 17" rims. Lowered HKS susp.

It is too damn low.

This explains why yours looks 'high' and mine looks low.

T.

It's my impression that the 400r bar + skirts are all rather conservative looking.

The skirts have some vent holes that do fark all and the rear bar is just a bit heavier set so it matches a big exhaust better.

It's only the front bar that looks a little loony.

T.

tony

your right only the front 400r bar looks loney, rest of the kit is pretty ordinary thats why im trying to chase up impul side skirts and rear bar for mine (i think the impul kit looks more aggresive.

p.s when are you going to give them trailer blinkers the flick? or atleast change them to clear one like mine..lol

Merli

corect me if im wrong but u where at eastern creek for the last street meet weren't you?

what times did you end up running?

look for my 33 racing out at the meets soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...