Jump to content
SAU Community

Car Difficult To Slide?

CAT_SPEW
 Share

Recommended Posts

Sleekman Contributor

Sleekman

Posted
Posted

a standard diff is useless for drifting (i beleive it only spins 1 wheel and its no where near as ez to control as a mechanical)

a 1.5 or 2 way lsd will keep u going hard all day long

brands like kaaz, cusco, nismo are all good

expect to pay around 1.5k for one (give or take a hundred or two depending on brand/shop)

or if your on a budget.... weld your diff together :D:D:D

scathing Grand Master

scathing

Posted
Posted

Most drifters opt for a 2 way LSD, so the car's attitude is consistent during on-off throttle.

And viscous LSDs (which I assume the S13 turbos used, mechanical LSDs weren't really prevalent back then) don't lock up too well. That's what makes them relatively "streetable".

If you're on a budget you could try using a more viscous fluid so it will lock up faster. Viscous LSDs are inherently 2 way, so it might suit your drifting needs. There is an aftermarket for VLSD fluid, although its not a big one since most people who want to "tune" their LSD end up going to a mechanical.

Anquetil Mentor

Anquetil

Posted
Posted
Suggestionsfor Brisbane southside? What should I be expecting to pay roughly?

Accurate Suspension (Woodridge) are closed til the new year, I usually go there.

Also highly recommend Tyrezone Cleveland, they have latest alignment equipment and setup drift cars. They will look after you.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...