Jump to content
SAU Community

Recommended Posts

Just recieved the lastest catalouge from our supplier

and thought this item might interest many people on here.

If 10 people are interested, then a saving of 50% can be offered

Free postage is also being offered anywhere in vic.

**UPDATE** no additional postage charges, will post anywhere in AUS

Product: 925 Sterling Silver Cufflinks

Design: Gear Shift

RRP: $49.95

GB Price: $25 (this price includes postage anywhere within aus)

gshiftng9.jpg

Product: 925 Sterling Silver Cufflinks

Design: Dice (contains cubic zirconia's as numbers)

RRP: $49.95

GB Price: $25 (this price includes postage anywhere within aus)

diceya0.jpg

If people are interested I can arrange many other items.

People so far...

Satanic (PULLED OUT)

1. phunky_monkey (1 g/shift) (AWAITING PAYMENT)

2. 9krpm (1 gearshift) (DIDNT PAY)

3. N1GTR (1 dice) (PAID)

4. oxford1327 (2 dice) (PAID)

5. tuitahi (1 g/shift) (PAID)

6. SNISMO (1 g/shift) (PAID)

7. kasanoff (1 g/shift) (PAID)

8. nuganen (1 g/shift, 1 dice) (PAID)

9. choyda (2 g/shift) (PAID)

10. Al-R33 (1 g/shift, 1 dice) (PAID)

11. Spook33 (1 g/shift) (PAID)

Edited by AWDMAT
Link to comment
https://www.sau.com.au/forums/topic/148157-gb-gear-shift-cufflinks/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Hi, can you pleae confirm that the dice cufflinks do have the "crystals" in them?

I've already got a set made in silver (just without the crystals)... no point getting another set if it's the same.

Thanks

Stan

Hi, can you pleae confirm that the dice cufflinks do have the "crystals" in them?

I've already got a set made in silver (just without the crystals)... no point getting another set if it's the same.

Thanks

Stan

checking for your mate

should have a definate answer boxing day or the following

List updated... 4 more to go...

Edited by AWDMAT

Cufflinks when coupled correctly with a business shirt can have quite an effect. Example; black shirt with shiny cufflinks always get attention - people actually stop and look at what they actually are.

They go in place of the buttons on your cuffs...

please put me down for 2 pairs of the dice instead of one as i would like a set for a mate of mine for a gift.

and are you guys really serious when you say you dunno what a cufflink is?????

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...