Jump to content
SAU Community

Recommended Posts

There are a few differences, one being the sensor plugs on r32 are round, square on a31. Also the r32 engine has a little more power in stock form. The r32 has factory bov and a31 doesn't. I have heard there is more potential for higher power outputs from the a31 engine, not exactly sure how or why though. Not sure on if the turbos are the same

Edited by Love_Hate

The cefiro inlet cam has a longer duration and the exhaust cam is retarded about 2 deg from the R32 cam.

ceff afm, coilpacks and ignitor are different.

ECU also only has 1 fuel map and 1 timing map as opposed to the skyline. it has 2 fuel and 2 timing maps.

If you look at the 2 maps the skyline runs 3 deg more timing and has different load tp scaling.

thanks for all the replys so with these spitfire plugs can u get spitfire coils that u can just plug in to replace the stock coil packs over coil pack problems?

They are adapters. http://www.skylinesaustralia.com/forums/in...mp;hl=splitfire Seems Splitfire didn't want to manufacture different coilpacks for the same engine. If you could get hold of a R32 coil pack loom and are 1/2 handy with electrics you could easily knock some up yourself.

They are adapters. http://www.skylinesaustralia.com/forums/in...mp;hl=splitfire Seems Splitfire didn't want to manufacture different coilpacks for the same engine. If you could get hold of a R32 coil pack loom and are 1/2 handy with electrics you could easily knock some up yourself.

so that is only for the adaptors then u would have to get ur hands on some 32 coilpacks to plug in them or do u buy the aftermarket ones as shown on the pics below the adapters ?

  • 2 weeks later...

the turbo is different also, R32 is ball bearing ceffy is plain bearing. also slight differences in the exhaust side.

later ceffys run the rounder R32 style loom plugs, but most are early ones

AFM, coils, CAS and some other sensors are the same as R31 Redtop RB20DET. turbo is also the same as that of a redtop.

loom (bar the plugs), injectors, head is all the same as r32.

while working on my dad's cef (series 1) I found that it had more parts in common mechanically (well, engine and electrics) with the R31 GTSR than it did with the R32 GTSt.

  • 4 months later...

i just found out that my R32 RB20DET engine is being run off a cefiro ECU...

can anyone tell me if this is dangerous for the engine?

i'm trying to track down an R32 ECU, but having no luck so far...

if anyone can help me by answering that question, it would be GREATLY appreciated... :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...