Jump to content
SAU Community

SA Wasteland?

MM2death

By MM2death,
in South Australia

 Share

Recommended Posts

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted

Looking at some of those bull’s eyes it may indicate you need a bit of bodywork or at least a high fill primer.

Did you say you are doing it all by hand?

It can be hard not to get rub marks in the car if you are doing it all by hand, can you at least get a block, or better still an oscillating orbital sander (air tool) to do the majority of the work. You will need to finish it off by hand, but to do the whole lot by hand is a big job.

PS any little imperfection will look 10 times worse with a coat of paint on it. Before you paint it get someone with a good eye to go over it and highlight the bits that need more work.

The first time I painted a car my preparation wasn’t good enough (after a week of work) and the car looked almost as bad with the new coat of paint on it.

Nozila Grand Master

Nozila

Posted
Posted

hey guy,

thanks for the advice. yeah the bull's eye are obviously dents in the fenders. im using a block and all by hand. Its a big job but i dont have the necessary orbitor equipment so im just going to have to do without it. Im ust concentrating on the sanding atm and then will fill up the dents prior to applying the primer. I aint rushing it so should hopefully be ok.

Sambo33 Grand Master

Sambo33

Posted
Posted
Looking at some of those bull’s eyes it may indicate you need a bit of bodywork or at least a high fill primer.

Did you say you are doing it all by hand?

It can be hard not to get rub marks in the car if you are doing it all by hand, can you at least get a block, or better still an oscillating orbital sander (air tool) to do the majority of the work. You will need to finish it off by hand, but to do the whole lot by hand is a big job.

PS any little imperfection will look 10 times worse with a coat of paint on it. Before you paint it get someone with a good eye to go over it and highlight the bits that need more work.

The first time I painted a car my preparation wasn’t good enough (after a week of work) and the car looked almost as bad with the new coat of paint on it.

:werd:

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted
Heya Sleeper, do you have some spare time in the next month to come down to morepower and get my turbo high flowed? Would be good to show them that I want the same service you recieved for the same price etc.

no problem. :Pimp2:

I have a week of from the 9th to the 17th :uh-huh:

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What brakes on R34 GTT(Europe)

      By Dose Pipe Sutututu · Posted

      Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...