Jump to content
SAU Community

SA Wasteland?

MM2death

By MM2death,
in South Australia

 Share

Recommended Posts

Cubes Grand Master

Cubes

Posted
Posted

Im a regular parmy eater.

THE absolute best parmy I've had quality and taste wise has to be from Billy Baxters in the Myer Center. The sauce they use is awesome, so awesome I've sifted through it with a fine tooth and comb and then copied the ingredients back at home.

A few Kalamata olives (do go light on these), a little capsicum few herbs and spices, fresh diced tomato's, olive oil + simmered for a while but add the capsicum a few mins before you pull it off the stove = FTW. :P

Don't go adding sugar to remove the tomato's tang/acidy taste, buy a better/different brand and or simmer with plenty of olive oil. Just the olive oil along + simmering is usually enough to bring the acid/tangy taste out of it.

The chicken they use is a good quality breast fillet, no brown bits no fat hanging off the end its all cleaned up nicely. And its FAT, not a bashed out or chopped in half through its guts chicken breast.

That massive parmy I had on one of the SAU meets I was a little dissapointed.

The Sauce was shit, no thought went in to it at all, it looked like tomato paste slapped on top, the chicken its self was thin and wasn't of the best quality, I had a few hard bits, black and fatty bits. :S

Billy Baxters in the Myer Center = Chicken Parmy FTW!

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Madaz Grand Master

Madaz

Posted
Posted

yeah was trying to be comical Luke forget where that line is from or how it even goes 100%

may be from the simpson's as all good things are

Flick been thinking and you may not have seen the 2nd rendition of your sig so i will point it out again and drop them back to back if you prefer the first then keep using it but take a look @ the 2nd also :laugh: and now 3rd :sorcerer:

1st you current one

flick2.png

2nd rendition

flick3.png

3rd rendition just did this one then after looking @ the preview post for a bit

flick4.1.png

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...