Jump to content
SAU Community

Recommended Posts

Ive got a very weird problem that started happening over a few weeks, and would only do it here and there now it does it 9 times out of 10 and its getting to be very annoying.

Basically my car wont stop running when i turn the ignition off... When i switch the key off and take it out all the dash lights go out, the clock dims, the stereo turns off etc but the motor keeps running... it acctually drops slightly in RPM but doesnt stop. A few times i have switched the key back and forward from off to on and the motor will stop.. but lately it just wont stop no matter how many times i jiggle the switch.. i basically have to put it in 5th and stall it to kill it.

Seems weird to me that the switch is powering everything off... except the motor/ecu etc.

FWIW i have done the fuel pump rewire mod running a power wire from the battery and a relay which is switchable from the existing fuel pump wiring... my turning off problem isnt related to this tho as it started doing it before i did the rewire mod. Plus ive wired it up properly on the relay :)

So yeah.. what could it be??

hey mate a similar thing happend to me when my car alarm stuffed up, it shorted out my turbo timer, so when i went to turn the car off, i couldnt becouse the turbo timer was in limbo land, sorta on like glowing but no info on the screen. so yeh fixed up the turbo timer and it was all good.

but anyway check ya turbo timer, may be the prob.

Ive got a very weird problem that started happening over a few weeks, and would only do it here and there now it does it 9 times out of 10 and its getting to be very annoying.

Basically my car wont stop running when i turn the ignition off... When i switch the key off and take it out all the dash lights go out, the clock dims, the stereo turns off etc but the motor keeps running... it acctually drops slightly in RPM but doesnt stop. A few times i have switched the key back and forward from off to on and the motor will stop.. but lately it just wont stop no matter how many times i jiggle the switch.. i basically have to put it in 5th and stall it to kill it.

Seems weird to me that the switch is powering everything off... except the motor/ecu etc.

FWIW i have done the fuel pump rewire mod running a power wire from the battery and a relay which is switchable from the existing fuel pump wiring... my turning off problem isnt related to this tho as it started doing it before i did the rewire mod. Plus ive wired it up properly on the relay :)

So yeah.. what could it be??

there is a small chance that there has been a turbo timer fitted at some stange, and when it has been removed there is some bare wire shorting out.

another possibility is that the turbo timer is still there and hidden up behind the dash. try letting the handbrake off next time it does it. if the car stops as soon as you do that then there is a turbo timer still fitted.

thought of all that and ive looked at the ignition wiring and none of it appears to have been spliced into at any stage, handbrake and clutch dont make it stop either so that rules that out. would the actual ignition switch cause this?

i don't think so, since the accessories are turning off.

no it can actually.

ahhem..

"would the actual ignition switch cause this?" YES IT CAN

the VL with same issue as yours, Accessories was also turning off, and a new ignition barrel fixed it. hello? go see an auto electrician, and he will tell you same thing.

cheers.

Edited by silverbulletR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...