Jump to content
SAU Community

Recommended Posts

Would not use one of these personally since there's no dampener built into it as there is in the OEM, NISMO & C's ones.

post-2420-1168206418.jpg

The dampener is built into the stick itself under ( part of ) the counterweight and helps to shift cleanly and as you can see, this shifter doesn't have a dampener built in.

I have owned and used a C's one which is about a 25% - 30% shift throw reduction and works great. To get the full benefit's your syncro's should be in top condition.

Also owned a NISMO one which is about a 10% - 15% shift throw reduction and works great but doesn't feel much different from the normal one.

Just my 2 cents.

  • 4 weeks later...
don't waste your money on them, they rattle and are really crap quality. The place that made mine even had the guts to imprint nismo on the side of the shifter.

Oh great! And they dont fit that easily too. My mechanic tried on Sunday and said that the shifter is the wrong size and all. The seller claims that it will fit and their solution was to sent me previous buyers email addresses and ask them how to do it! Not happy Jan!

:laugh:

got one for my car from ebay, paid $57+ postage total, didnt have any instructions with it, but once i sorted it all out and eventually got it in (was a bit tight) it felt a bit crap untill all the parts wore in which took a week, now it feels BEAUTIFUL, so happy with it, definately some of the best money ive spent on the car... had it for 6months now and no problems... looks exactly like the one in the first pic...

driving anything else feels like a tractor!

I have one of these in my 32gtst, looks exactly the same, they are counter weight balanced, and are a solid feel without the damper, feels better like that than the original. My throw seems to be 50 less.. which is great, wouldnt go back. Easy to fit, but the little white cup on the end of the shifter didnt fit into my slot in the box, so i had to change that from my original, does have a little rattle, but sound deadner under the gear boot has fixeed that. For the price, best way to go, reliable, easy to fit.

Just took ownership about ofa an R33 GTS-T a couple of weeks ago and the car was fitted with a (very rattly)C's copy shortshifter.

Over the weekend (the first time shifting a little agressively) the whole shifter came off. The plastic insert (that goes into the small ball at the end of the shifter and into the selector) had split. It's back in there for the meantime but I have to shift slowly.

My question is: is this part included in the eBay kit? Having never seen the standard shifter I'm not sure if this was a stock Nissan part?

Can this part be purchased seperately from Nissan?

Cheers for the help,

Aaron.

just blocked the noise getting into the cabin. you cant fix the rattle as it is the lever inside the box.... not the rings underneath as you may be thinking. But works an absolute treat!
Edited by aaron_25t

hey guys

ive been looking for a while to get a short shifter into my 33, and spent a lot of time contemplating which to buy: C's, Nismo or the cheap copies off ebay, until the other day i was on ebay and some how came across and oridinal Tomei short shift kit but was second hand. it didnt bother me though and it had a buy it now price of $140 so i bought it.

i put it in myself with the DIY instructions off an SAU member.

perfect fit, no noises, tight and reduced the throw by at least 35-40%.

i suggest listen to what most people have to say and buy the right parts for your beloved baby, invest in only the best

thats my two cents

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...