Jump to content
SAU Community

Recommended Posts

just get a few washers and put them in the hinges to lift it up a little i did it with my old car for similar over heating issues cooled down pretty quick after that 1 cm is all the lift it needs but it does look kind of random and i think its illegal (cop pulled me over told me to take the washers out or he would fine me) so give it a thought

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

just get a few washers and put them in the hinges to lift it up a little i did it with my old car for similar over heating issues cooled down pretty quick after that 1 cm is all the lift it needs but it does look kind of random and i think its illegal (cop pulled me over told me to take the washers out or he would fine me) so give it a thought

A vent near the front of the bonnet for the radiator air would be ideal, that way the rain only falls around the gap between radiator and pulleys.

Spacing the bonnet up at the rear does wonders too. The downside is engine smell when you activate the interior vents. On GTR's you only need to remove the rubber seal at the point where the rear of the bonnet meets the area in front of the windscreen. That works the same way.

Here ya go Dan, a pic of the ZTUNE bonnet on a R33GTR...

gallery_1569_106_76901.jpg

Main reason I put it on is coz it sees a lot of track time as well as street use...

The most I've seen my car reach is 91degrees on the Power FC controller.... mind you it has 350rwkws...

It used to be carbon, but painting it silver keeps away the unwanted attention....

Jack the car looks awesome with the bonnet painted silver, nice move. :sorcerer:

If i was to put a bonnet on my car, this is my favorite. It has all the vents in the right places; behind the radiator and above the turbo, manifold, etc.

post-1811-1168606307.jpg post-1811-1168606420.jpg

What do you guys think about that little triangle vent on the bonnet of r34 gtr's? Im not sure if its a vspec bonnet or wat, but its towards the top right hand corner of the bonnet. Im sure its there for a reason, but the way I look at it, i doubt it could help bring down temperatures much, if at all.

I thought it was to get air to the turbo housings?

Oh. :S What do you mean get air to the turbo housings? Like to cool the turbos? Stock turbos are gonna be low mount anyway and that vent is factory id say?

Yeah that's what I was thinking, coz it sits around there and I know what u'r saying but can't think of another reason to be there. push hot air down and under car?

It's to allow hot air out, that's why it is positioned above the turbos; that's also why i like the bonnet i posted.

Hot air rises :laugh:

any way you go with venting is going to have a positive effect on cooling.

your now just worried about rain? most of the engine is waterproof. or should be so there isnt that much of a problem. and while its running thisgs are pretty hot and water isnt too much of a worry.

p.s. whats rain?

lifting the back of the bonnet is a pretty good idea. a decent bonnet will cost around $1000 and you would be better spending that on a tripple core radiator or a davies crage water pump or more power so lifting the back of the bonnet up is a cheap and afective way for sire. the washers under the hinges is a bit dodgy thoe you would be better off getting a few bits of steal or aluminimum the same size of the hinge and some longer bolts to do it properly.

also removing the rubber strip will help and that alows the bonnet to stay nice and flush. thoe like mentioned before you will get the smell of the engine in the car when turning vents on. but if you have an oil breather like me this wont matter anyway because i can always smell my engine.

on my old r30 race car i simply cut a hole out between the top of the radiator and the cam cover and when the car is sitting there you can see the heat floating out the vent. if it wasnt venting than it would be circulating in the engine ay going no where.

another experiance i have had is when my exhaust temp sensor has been sitting on the turbo housing (before being installed) when the car is running it may get up to 300 deg and after 30 secconds of the engine being switched off the temp is up to 350 to 400 deg.

so basicly it gets very hot and the more you can do to stop it the better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...