Jump to content
SAU Community

Recommended Posts

just saw a pic of kenny's bmw at wsid from a meeting just prior to xmas on cackling pipes

howd it go champion?

Shane, fourth time outto WSID in this trim and fourth problem. The car developed a misfire on the first pass so back on the truck and back to the workshop :-(

do i recall you saying you had bolt in intrusion mate, what ws the comment from tech inspector, i tried to make a rule submission to allow sub 10 but higher than 9.00 cars aloud to run bolt in with 6 point as they do in NHRA, but i was told insurance company is what will not allow it so no point putting the $25 in to try. apparantly it has been asked many times in the last 2 years.

im going to have to go full 6 point in the next couple of months with the new package, not liking the idea of no street driving.

do i recall you saying you had bolt in intrusion mate, what ws the comment from tech inspector, i tried to make a rule submission to allow sub 10 but higher than 9.00 cars aloud to run bolt in with 6 point as they do in NHRA, but i was told insurance company is what will not allow it so no point putting the $25 in to try. apparantly it has been asked many times in the last 2 years.

im going to have to go full 6 point in the next couple of months with the new package, not liking the idea of no street driving.

Yes I do have a removable bolt in intrusion bar in the driver's side, however the rest of the six point cage is fully welded in. It is ANDRA tech inspection legal when you follow the rules with regards to sizing, etc.

You can get a six point cage engineered for street use.

  • 2 weeks later...
Yes I do have a removable bolt in intrusion bar in the driver's side, however the rest of the six point cage is fully welded in. It is ANDRA tech inspection legal when you follow the rules with regards to sizing, etc.

You can get a six point cage engineered for street use.

But you cannot get a six point welded in cage engineered for street use.

Best of luck with the BMW's drag racing.

But you cannot get a six point welded in cage engineered for street use.

Best of luck with the BMW's drag racing.

mmm

i was reaidng a release formt eh RTA last week and it said 6 point was a no no and couldnt be engineered, the way i read it though if it was engineered before a certain time, then you are fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...