Jump to content
SAU Community

Recommended Posts

Hello all,

I have done a search on this problem i have on the forums and have got a bit of information, some of which seems to contradict the other. So just wondering if anyone has experienced this/knows a fix for it. Here goes:

I took the car for a wheel alignment and balance cause i had bad vibration over 120km/hr. Guess what? It's still there. It's violent between 120-130km/h. I've noticed that at 120km/h it vibrates through the steering wheel. 130km/h, the vibration in the steering wheel is less, but the console (where the radio a/c is) shakes like hell. At 140km/h, the vibration moves to the drive shaft/rear i think. Any ideas on what this could be or how i could fix it?

Thanks in advance!

Cheers,

Eek

Link to comment
https://www.sau.com.au/forums/topic/15208-help-with-vibration-problem/
Share on other sites

sounds like ur wheels aren't balanced, try someone else to balance it... also test the pressure of the tyres, try not to use the ones u find at the petrol stations cause they aren't very good, i find that my tyres don't seem to hold pressure very well so i have to keep pumping air in every now and them ... but yeah ... most of threads like this i've seen were fixed with proper balancing... are the tyres new??

i think its an unbalanced tail shaft, on my vl (yeah its not a skyline) i had a 2 peice tailshaft, wheels were ballanced and alligned propley, coudlnt work it out, but it would be find till i did 160 and it would vibrate like hell. i replaced the center berring thinking that was ruined, didnt do anything.

my car was so bad once backing off at 240, u would think it was going to drop the box and send the engine outa its mounts.

i then got the tailshaft ballanced and everything was fine.

have you hit anything under the car? the slightest knock on a tailshaft can put it outa ballance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...