Jump to content
SAU Community

Recommended Posts

Dear all,

Anyone know what the strut bolt torque spec (how much I should torque it when screwing it back in)?

(the one you take off to install a strut brace?)

I've been trying to find the information before I unbolt/unscrew it.

These ones:

strut.jpg

Thank you.

Link to comment
https://www.sau.com.au/forums/topic/152453-strut-bolt-torque-spec/
Share on other sites

If you snap that bolt using a spanner, you must be a muscle man.

Just use a spanner of the correct size - 13mm from memroy, do it tight with the spanner, and you'll be right. Just be sensible. Like do it tight with the 13 mm, not f**k off tight.

You'll have a problem overtorquing if say you used a breaker bar or something, but generally, you'll be fine.

The tps bolts are different - they're a small bolt.

Okay, I've done it for 35 ft-lb with a torque wrench, should be good.

Took two and a half hours to install the engine damper, that engine lift plate (whatever it is called) bolts are hard to unscrew and tighten, trying not to disconnect anything.

i snapped the rear strut bolt when tightening it after installing my rear strut brace.. so its not unheard of

costly exercise to source a new strut top asap to get the car back on the road...

Waz, how tight did you do it? Like just reasonable? Or crazy tight?

What did you use to tighten it? a spanner? or a breaker bar?

I've found, after a while, you get the hang of how tight certain things should be. If you use a spanner, you can actually tighten it to within the torque spec. It's hard to describe, but you get the hang of it after you do it many times.

yeah i was doing it pretty tight but that wasn't the problem really

because it was a rear brace i was in the boot trying to use a spanner and ended up resorting to a ratchet but there's not much room to move the handle in there

and the problem came when i not only was trying to tighten it but was off balance and introduced some angle on the handle of the wrench causing the bolt to shear off!

my bad.. you learn form mistakes better than anything

  • 1 year later...

did this just before....however i induced no angle into it, and the bolt appears to have a failure caused by torsion shear (twisting shear in the plane of the thread). It was simply replacing the stock lock nuts, and was barely even tight which leads me to believe it was caused due to over tightening previously and this exercise threw it over the edge.

Anybody got any tricks to get her quickly back on the road?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...