Jump to content
SAU Community

Recommended Posts

So I've go ta 2wd dyno day comming up (in the 'gong) the 4/2/07 for anyone interested check the cruise thred.

Anyhoo, problem is. Can I turn the R33 GTR into a 2wd by pulling a fuse the same way you can on a 32? :(

Thanks....

32 only.unless you want to stuff ya transfer case.. i think by memory you will have to take out drive shaftso it dont wear..

correct if im wrong

Yep. Along those lines. The R33 and 34 GTRs run a preload on the transfercase clutch pack so it'll do some bad stuff to clutches.

Pull drive shaft to front diff if you want 2WD.

K- thanks.

Thought so.

I have a HKS pro torque splitter (in cabin), but doesn’t always switch over to full 2WD.

Does the HKS torque splitter remove the chance of clutch damage? I just got a new twin plate clutch last week!

it's not clutch damage that is a problem. it's transfer case damage. it's simple for 33 and 34 GTR disconnect the front prop shaft (sends drive from the transfer to the front diff). otherwise your front wheels will not be moving, but the transfer case will be trying to send a small amount of drive to them, this will wear out the clutch packs in the transfer case (not your clutch in the gearbox).

OIC - but will my HKS torque splitter avoid this damage in the trasnfer case?
32 only.unless you want to stuff ya transfer case.. i think by memory you will have to take out drive shaftso it dont wear..
I might be wrong, but with my mates r33gtr we just popped in no gear then turned it off slowly and it went in 2wd

shouldnt do, that trick works on r32's only >_<

r33/r34's cant be fully switched to rwd only unless you undo the prop shafts like its been said. The hks toque splitter will only change with percentage of power sent from the motor to front and rear wheels, there will always be a small amount of power going to the front wheels even with the torque splitter fully adjusted to rwd. Just the way it is unfortunately...

first post btw woooh woooh woooooooooooooooooh

Edited by R34GTFOUR
shouldnt do, that trick works on r32's only :)

r33/r34's cant be fully switched to rwd only unless you undo the prop shafts like its been said. The hks toque splitter will only change with percentage of power sent from the motor to front and rear wheels, there will always be a small amount of power going to the front wheels even with the torque splitter fully adjusted to rwd. Just the way it is unfortunately...

first post btw woooh woooh woooooooooooooooooh

first post & spot on the money...ended up proping the front end of the GTR up (edit: cause it was too much hassle to pull the prop shaft) & running it with the torque splitter sending everything to the rear. But as you said the front wheels still turned & it lost power at the rears due to the fronts free wheeling...

Still screamed like a banshee thou... :P

thanks to D_I_F for the youtube clip...

Edited by double overhead sun visors
  • 3 weeks later...

You CAN make an R33 GTR real wheel drive only, WITHOUT removing the prop shaft. I have done this many times for dyno runs.

Under the drivers side dash, there is a small brown plug with a yellow wire.

Disconnect this with the car turned off.

Then when you start the car, pump the brake pedal 8 times in 5 seconds and you will see the light flash on the dash. Then drive the car forward for a little bit to complete the depreasurisation.

This de-preasurises the centre diff housing, but also disables the A-LSD diff on V-Specs, but this is no problem on a dyno.

Once the key is tuned off, this resets the centre diff to re preasurise

This information came from the towing recomendations section from the skyline service manual.

Hope this helps!

  • 1 month later...

i'm not quite sure what you mean by drift ready. yes it's 2WD but I'd wouldn't call it drift ready. 32 GTR doesn't make a good drifter. lots of reasons why.

btw, dynoing your 33 GTR with the front of the car resting on a jack would have to be one of the sillier things I've ever seen someone do.

  • 3 weeks later...
Is a 32gtr drift ready just by unplugging the 4wd fuse n disabling 4wd?
haha this deserves a flaming.. im guessing your under 21...?
i'm not quite sure what you mean by drift ready. yes it's 2WD but I'd wouldn't call it drift ready. 32 GTR doesn't make a good drifter. lots of reasons why.

btw, dynoing your 33 GTR with the front of the car resting on a jack would have to be one of the sillier things I've ever seen someone do.

got a good clip of a BNR32 drifting.. but yeah.. lots of issues.. weight being one.. and early GTR have oil issues.. RBs dont like being reved high for long..

LOL at guy resting a car n a jack.. while dynoing...

i wanna see pics lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
    • You have no idea how many goddamn boxes I received these past three months haha Most have been put to use by now though, luckily
    • Not going to pretend I didn't do a bit of junky work this time around, but mostly due to the fact that some things I am not willing to spend days fixing right now, like wiring. I try to do most things properly the first time around.
×
×
  • Create New...