Jump to content
SAU Community

Recommended Posts

hmmm... it apparently had the wrong oil filter when it came over from Japan a year ago, so perhaps the damage was already done by the previous owner and it just hung in there long enough for me to break it?

I would know if I had starved it of oil because the oil pressure would indicate this? ie driving around with unacceptably low oil pressure.

I will definately make sure it is as terminal as suspected before I replace or rebuild but it was diagnosed by 2 very experienced import gurus... so I have been scratching my head... a lot.

What is the best method of diagnosis, compression test? leakdown test?

But new engine blocks don't have any numbers, so there is no "original number" to bring up. Stamping of damaged block numbers on replacement blocks is of course completely legal, otherwise Nissan (and the other manufacturers) would not be able to sell new blank blocks.

Call me cynical, but in many cases I don't think they even check too closely.. when i bought a car recently I wrote down the engine number on the reg papers - response: "this is not the engine number on file" .. me: "guess it must have had the engine changed then", them: "err, ok, probably, what is the new engine number?", me gives new engine number (not checked.. might have even got away with rb26xxxxxxxxx), and away we go... good 'ol QLD..

hmmm... it apparently had the wrong oil filter when it came over from Japan a year ago, so perhaps the damage was already done by the previous owner and it just hung in there long enough for me to break it?

I would know if I had starved it of oil because the oil pressure would indicate this? ie driving around with unacceptably low oil pressure.

I will definately make sure it is as terminal as suspected before I replace or rebuild but it was diagnosed by 2 very experienced import gurus... so I have been scratching my head... a lot.

What is the best method of diagnosis, compression test? leakdown test?

Wrong oil filter :headspin: , that makes no sense either. If the oil filter leaked you would know about it, oil everywhere. It can only then get blocked, in which case the bypass kicks in and the oil stills flow at normal pressure. It just doesn't get cleaned. You can tell if that's the case by looking inside the cam covers, no filter = dirty scum.

Compression test or leak down test tells you nothing about bearing condition. Noise is the best test, main bearings rumble like a heavy train on railway tracks. Big end bearings knock, like someone at the front door. As you free rev the engine the noise dies down and as you back off it comes back louder. Once heard it is unmistakeable. The other test is oil pressure, a good quality gauge will fluctuate with bad big ends. The needle flicks around as the oil pressure jumps as it feeds that crook big end bearing.

I suggest you find an old mechanic, he doesn't need to know anything about imports. A big end bearing knock is a big end bearing knock. He will pick it in an instant because it used to happen a lot. A lot of young mechanics have never heard a big end knocking because it doesn't happen very often these days

Hope that helps :D

Thanks that helps alot...

my gf's dad would qualify as an 'old' mechanic lol... maybe time to tow it to his shop... If it does end up being a terminal problem would you go with renowned import specialists and pay the $$$ or go with the family member mechanic who will make the labour costs minimal (is not experienced with modern turbos, though still a good mechanic)?

You make the decision, talk to a few places you would like see do the work, get a firm price and hold them responsible for their work and the price. An engine rebuild is big money. Some say 2k isnt big money, but thats 2 months work for me.

Why is it mechanics refuse to given written quotes, is it a time thing. It would be cool to see a quote that says, Price X in labour, price X in parts so you can compare apples with apples.

Worst case scenario you could be wary of the buck fitty quote as you know they havent allowed for certain things, or you can see that they are actually just good operators with low overheads.

Hope you get it back on the road soon with as little pain as possible. if your car is relatively std, turbo, injectors ecu and boost, then wrecker motors often come with 3 month warranties etc etc. So thats $2000 (?), sell your head etc for $500-700, sell off the bottom end etc, or just throw new bearings in your RB25. A std nissan engine takes a good flogging if you have the std turbo hanging off it.

Talk to ppl you trust and see how you go.

Its not just going to cost for the engine rebuild its also going to cost extra for the head welding which could possibly involve R&R of the valves etc.

Then there's the ECU. You will need a powerfc.

Get the motor in get it tuned.

Run the motor in get it tuned again.

There's a lot more initial money invloved with the rb30 than simply slapping a set of bearings in the rb25.

yeah I've got quotes on dropping a new (wrecker) engine in and pretty much know how much it will cost. I'm not too stressed about that as I know I can have that work done cheaply and reliably and be back on the road relatively quickly.

I just want to weigh that up against going for a rebuild and I really haven't got an solid quotes on that to have made a decision yet. It would be a shame to spend $2xxx on putting it back the way it was...when for a couple of extra grand I could have a relatively stock but tough and tourquey 3L motor?

I guess the first decision is whether or not to pay to have the engine stripped to see exactly what the damage is? ... or just out with the old... in with the new...

thanks for the comments guys...

Its not just going to cost for the engine rebuild its also going to cost extra for the head welding which could possibly involve R&R of the valves etc.

 

Then there's the ECU. You will need a powerfc.

Get the motor in get it tuned.

Run the motor in get it tuned again.

 

There's a lot more initial money invloved with the rb30 than simply slapping a set of bearings in the rb25.

Oops, i wasnt actually referring/comparing to the RB30 :Oops: , just commenting on how to cheaply /sensibly get the car back on the road :D

I don't consider a 2.6ltr second hand motor a much better outcome than a bran spankin' 3ltr.

It would be more than $1000 to fit as you first have to remove the old motor then drop the rb26 in.

The rebuilt, blueprinted, balanced to race spec (heinz), crack tested (block, rods & crank), forged pistons, multilayer metal headgasket, fitting of the head, cam belt & relocating tensioner set me back $3700.

The head reco, port inlet/exhaust, polish exhaust, roughen up inlet & deshroud inlet valves cost ~$1100.

Total - $4800

+ R&R ($2000) it would come up around 7k.

If you think you can buy a RB26DETT and drop it in without bugger all extra expense think again. Expect turbo's to be replaced and a motor that may have been thrashed or a motor that is a little long in the tooth.

Eventually needing a rebuild with forged pistons anyhow.

People build the 3ltr because they want response, torque and a linear less snappy more tractable hi-po 250-300rwkw+ motor.

Yeah stock second hand GTR motor.. dime a dozen here for around $5k... I wouldn't use a second hand one with stock turbos if I was going to drive it seriously.

On that note I just painted my engine bay and got a new swaybar that goes around my sump so the RB30 will be dropped in and lowered as much as possible. :D

Well I was just thinkin bout the cost of my engine rebuild for RB30DET. It did not cost me anywhere near $7,000. Details...

Note that everything is pretty much at trade price & mates rates prices.

Block $100

RB30E Re-ring kit + bearings + Genuine nissan head gasket $440

Rebuild engine hone block machine crank pins to over size / clean deck block $330 (Mate)

Engine Mount $125

Clutch Plate $105

Exaust Manifold Studs $60

Mate at his own workshop to store car and do work after hours after work or weekend, he supplied everything needed from VCT setup to sending head away to be cleaned and reconditioned with new valve stems / competition fittings for sump for VVT oil drain & Turbo oil drain labour to remove engine dismantle and put all back together was only $2900.00 (+ many nights on the piss)

So totally cost me abouts $4000.

I think I got a great deal from my mate to do the RB30DET Conversion. He basically chucked in a free head rebuild and used new manifold gaskets.. I also put countless hours of work into it doing it with him.. The outcome was awesome but took us 4 months to do.

Pays to have mates in the trade. :P

 

7k I would think would include a set of Forged pistons.

 

RIPS from NZ can ship RB30DET's complete with head for around the 4.5k mark.

No 7k was drive in drive out with a $50 wrecker engine without even cracking it open. (developed a engine knock later)

I think he supplier head and turbo and manifolds also. it was a NA VL.

well considering the engine had to be supplied by customer - and thats what he choose to start off with.....

The 7k including head manifolds vg30 turbo rb25 wiring harness all vct setups etc etc engine pulled out built up and installed and tuned... dunno bout the intercooler

That doesnt sound too bad does it ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...