Jump to content
SAU Community

Recommended Posts

For the price fo $1400 just for the Greddy plenum, you can save that and buy an rb26 head like i'm doing.

The rb26 heads also flow better.

Thats also my thinking. Its not so much they flow better its the better factory cams + the added bonus of the solid followers = higher ramp rate. higher lift for a given duration.

Providing you can pick up a rb26 head and manifolds for a reasonable price.

Edited by Cubes

Every 6 months i end up in the same position...I want the thing to look completely std, heat shields and all. So what is so difficult about getting a few offset braces made wo that it goes behind the throttle body??? Does it clear the actual manifold.

Be great is someone could put a telescopic aeiral on their rocker cover and measure the height to the top of the plenum & top of throttle body. Then close the bonnet and measure the ehight to the underside of the bonnet. Liek to know the clearance to th eunderside of the bonnet as well:)

I've done a few measurements.

Just in front of the throttle body the plenum has 20mm with the motor lowered 13mm.

If you drop to your knees on the drivers side of the engine bay you will see where the cross over pipe is higher than the throttle body and plenum, it almost v's up a little, I had a good look at the cross over pipe, its not touching the under bonnet lining but must be damn close as it too sits 20mm higher than the plenum section where the strut brace would pass over.

The strut brace will no way fit over the throttle body and cross over pipe. I suspect one of those flat tubular style strut braces will fit providing it passes in front of the throttle body/cross over pipe.

All else fails you could always grab a r33 rb25 or rb26 stuffed bottom end (piston oil squirters a must for cast pistons that see track work), Rebuild that with cast pistons and throw a r32 rb25de head on it. That would look 100% stock.

Edited by Cubes

It really is a hard decision.

When purchasing my head I found a 26 head and inlet manifold for 2.5k.

The 25 head was $750 + $1100 for rebuilding and port/polishing.

I decided the 25 head rebuilt was a better option for reliability. I didn't want to try my luck with a second hand head even though it would have no doubt been fine.

I wonder which would flow better, a 25 head that has been ported polished, the suitable valve jobs, inlet valve deshroud, port match and 260duration exh. cam or a stock 26 head.

The reason for a 260 duration exhaust cam... From flow tests i've seen its the exhaust side of the rb that has issues. Not the inlet.

I could be wrong. Its only my observation.

Thats the thing, CUbes and myself were looking for the heads for our motors almost 3 years ago now...a lot has changed in that time for skylines. Especially prices for parts.

Saying you can buy GTR heads for $1500 now doesnt reflect the almost $3k price tag back then :P

The only difference between the two looms (being an r32 without vct) is the inlet air temp sensor addition.

After all all you need to do is route the existing loom plugs to the new rb26dett locations. Not too hard at all.

Edited by Cubes

Warning!!! ACL PRODUCT WARNING. Were supplied new race series forged ACL pistons, rings and bearings for an rb30/25 hybrid. Engine built buy a reputable engine builder and run in by ex Perkins engineering mechanic/tuner. Rattled from new and finally pulled it down at 2000Klms to discover massive wear on the drive side of the bore. Piston to bore clearances measured at 7 tho and within spec. ACL denied refund/replacement and rolled out these excuses in this order. 1. Detonation (cleared after hardness test) 2. Foreign substance in bore (brand new engine run in on dyno with standard air box and new filter) Cleared after excuse number three. 3. Over boosting causing rings to break down and cause abrasion on bore. (Stat decs signed by engine tuners stating run in boost set to max of 14psi). ACL now tell me that there FORGED race series pistons are only rated for 10PSI. This engine has a comp of 8.2:1. Standard engine runs 9:1 with cast factory pistons at around 9psi...do the math. Currently taking legal action. Any questions regarding this "race designed product" PLEASE contact me @ [email protected] .This is not a rant, but an opportunity for other people to learn from my experience.

post-1044-1129037615.jpg

ACL now tell me that there FORGED race series pistons are only rated for 10PSI

Theres a reason why they are rated at 10 PSI, they aint forged pistons!

I've been selling ACL parts for years and they are yet to make forged pistons. Someones been feeding you bs.

Alot of people take the RACE series brand to be forged when they are a better grade of cast.

Edited by retrotec

on a side note, i find it hilarious that a piston can be "rated" at 10psi.

does that mean the piston will be okay on a motor with 10psi, huge back pressure, poor camshaft design and 14:1 compression? or does that mean that the piston will be okay on a motor with 10psi from a blower, with no back pressure, a perfectly selected camshaft and 7:1 compression?

on a side note, i find it hilarious that a piston can be "rated" at 10psi.

does that mean the piston will be okay on a motor with 10psi, huge back pressure, poor camshaft design and 14:1 compression? or does that mean that the piston will be okay on a motor with 10psi from a blower, with no back pressure, a perfectly selected camshaft and 7:1 compression?

it's a bit like wankers who ask you about your car and their first question is "how much boost u running bro?" :blink:

But I think this guy is talking about the acl hyperlite series of pistons, I was considering them for my conversion, but my engine builder talked me out of them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...