Jump to content
SAU Community

Recommended Posts

hey ppls

i was doing some tests tonight.. and i noticed when im at like 14psi @ 5000rpm doing like 100km in 3rd the injector duty is only 50%.. does that sound right for stock rb25det injectors and a sard fpr ?? the turbo is a hks 2535.

does it jump upto 90% or something realy high in the last 2000rpm ??

i know i could test btw... but dont have many points on the ol licence left.. :)

Link to comment
https://www.sau.com.au/forums/topic/154694-injector-duty/
Share on other sites

hey ppls

i was doing some tests tonight.. and i noticed when im at like 14psi @ 5000rpm doing like 100km in 3rd the injector duty is only 50%.. does that sound right for stock rb25det injectors and a sard fpr ?? the turbo is a hks 2535.

does it jump upto 90% or something realy high in the last 2000rpm ??

i know i could test btw... but dont have many points on the ol licence left.. :P

Depends if your foot was to the floor or just holding 100km.I often go over the 90% duty in my car with 10psi and standard turbo.Thats the reason i have a set of 555s on the way :)

Link to comment
https://www.sau.com.au/forums/topic/154694-injector-duty/#findComment-2877717
Share on other sites

nah my foot was down.. not flat, but maybe like 3/5 down. it was at 14psi also..

ill try do more tests today and see how high it goes

I would've thought 50% was normal because you're only cruising at 100km/h (albeit in 3rd and at high revs) but you're not on boost etc...put your foot down and it'll probably go up to 80-90% etc...
Link to comment
https://www.sau.com.au/forums/topic/154694-injector-duty/#findComment-2878073
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...