Jump to content
SAU Community

Recommended Posts

Hi everyone,

Im long time reader, first time writer.

I have a big problem with my Skylines Brakes :sleep:

It seems as if the brake shoes are wedged into the Disk rotor and i cant get it out.

I've tried using the two bolts to remove the rotor, but it pulls the entire hand brake assembly out with it as well. Would anyone know how i can readjust the hand brake so that i can remove the rotor.

I'm afraid if i try remove it any further using the bolts, ill rip the entire hand brake off n needa buy a whole new assembly which = more money :bomb_ie:

I've also heard you can adust the handbrake from the plastic cover on the rotor, but i cant seem to understand how to adjust it. Do you push it in or do you turn it with a long nose plier? It cant be adjusted with a screwdriver as the face is flat.

And yes, i've released the handbrakes when i tried removing the brakes. I also tried whackin it with a hammer but the top of the rotor wouldnt even budge! The handbrakes seem wedged into the rotor.

Is there a secondary backup adjustment that i can do to loosen the brakes b4 removing the rotor?

Please help someone!!

My skylines currently doin 15L/100km with feather like acceleration.

Thats to high for this car =(

Thanks EveryONE!!

=D

Link to comment
https://www.sau.com.au/forums/topic/154995-how-to-remove-disk-rotor/
Share on other sites

The shoes are adjusted through the 1/2" hole in the rotor hat. The adjustment is near the "7 o'clock" position. You will need a flat-blade screwdriver to undo the adjusting wheel.

But how do you undo the adjusting wheel if theres nowhere 2 wedge the wheel fingy. Inside is just a plain round metal thing. The only thing i can fink of is using a long nose plier 2 twist and readjust.

Has anyone had this problem before?

The shoes being wedged stuck to the rotor so that you cant remove it wifout adjusting the handbrakes?

Ill try it when i get the chance.

Cheers

Back off the handbrake adjustment in the cabin, and then disconnect the cable at the balance bar which sits infront and above the diff housing.

You may just have too much tension on the handbrake so its holding the pads on.

hmm we need a pic of the hole....there is an adjuster in there somewhere....back it off from the cabin as much as you can first though (small nut on the handbrake cable at the lever).

The handbrake is off isn't it?

hmm we need a pic of the hole....there is an adjuster in there somewhere....back it off from the cabin as much as you can first though (small nut on the handbrake cable at the lever).

The handbrake is off isn't it?

Yes the handbrake is off. LOLZ and its lowered 2 d max already.

Still handbrake wedged in rotor. Still cant get the adjustment 2 work, l mite try release the centre adustment as well.

Thanks everyone

Yes the handbrake is off. LOLZ and its lowered 2 d max already.

Still handbrake wedged in rotor. Still cant get the adjustment 2 work, l mite try release the centre adustment as well.

Thanks everyone

you may have lips on the inside of the rotor, making it hard for the lips to go over the hand brake shoes, if this is the case you gotta get em off any way you can and remove lips or replace rotors, thats if you REALLY need to get em off :no:

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...