Jump to content
SAU Community

Recommended Posts

Having likely found the wheels to get, now the question of tyre size arises.

OEM tyres on a S2 Stagea is 225/50/16 which gives a diameter of 631.19mm

Looking at 18" x 8" rims

Possible tyre choices (based on 1010tires.com) are:

225/40/18 - diameter of 637.03mm

235/40/18 - diameter of 645.16mm

245/40/18 - diamater of 653.03 (per tyre retailer)

245/35/18 - diameter of 628.65mm

Therefore based on the above, it seems the closest tyre would be the 245/35.18 and then the 225/40/18 (although have noticed in previous threads that the 225/40/18 seems to be the recommended tyre size).

Will check with dealer on the 245/35/18 size. The tyre retailer also stated that the 225/40/18 would be too small in overall diameter whereas the above suggests it is actually a larger diameter than the OEM version.

For those who are running 18" rims (or just know this stuff) can you advise on what tyre sizes you are running and whether you have noticed any problems?

Any help woule be appreciated

Cheers, Al

Link to comment
https://www.sau.com.au/forums/topic/156856-help-with-tyre-sizes/
Share on other sites

if you HAVE to base it on that

I dont listen to tire manufacturers

they tell people things dont work becuase most people are retarded and do stupid things.

225x40

if you want to go lower you can go 215/40

but some people think its unsafe. its not.

But hte need to go with a smaller tire has to do with a few things

First

How low is your car?

Im running small tire sizes becuase i like to tuck tires in my wheel wells.

if you dont need to do that

go with a 245 or so its "Safe" or whatever

but larger tires on 18s looks funny. and it will make your car sit higher.

Edited by yokotas13

Hi Alan,

Pretty sure you are asking the question in regards to keeping your speedo accurate (which is very important in Australia Grant) and you are dead on the money, the 225/40/18 is the closest you can get to the factory rolling distance in a standard 18" tyre. Although the 235/45?/18 is a more common size and can be a lot more cost effective solution without getting too far away from the factory rolling distance.

You can use the following page to work out the difference between the sizes.

http://www.carbibles.com/tyre_bible.html (scroll down a long way).

I have a S1 running 225/40/18 tyres and under the freeway speed check I read 97 when sitting dead on 100km/h so I am happy with that size.

Cheers

Luke

Luke, yeah it is in relation to speedo accuracy to get the closest to the OEM diameter

Logan, my tyre placard has both the 205/55/16 and 225/50/16 on it and I have the 225's on there at the moment

So still divided opinion it seems :)

why is the speedo so important?

Keep a second set of wheel so when inspection comes around, you have a stock rolling diameter wheel.

i do it. its important in japan too

spedo is important here grant because unless u run a gps all the time im buggered if ill fork out the huge dollars for speeding fines here in nsw and believe me ive been done for 5 bloody klm over the limit.not in the stag tho was by a fixed speed cam

As Mike said depending on other things, you can get fined for 2kmh over the limit in WA so having it as close to OEM is a factor over here.

So it seems a toss up between 225 and 235's without any mention of the 245's - would 245's actually fit?

I have 18X8 and 235/40's fitted.

My speedo reads pretty much spot on (+/- 2km/h).

I also am not a fan of the stretched look with tyres. I like it when the edge of the rim and tyre are even. The stretched look just makes it look like you are too cheap to buy a set of proper width tyres (IMHO).

I would have liked 245's, but I heard that they don't fit very well on the front.

but the problem is you guys ar emissing the point and advantages of streching

i wont get into it, but its just not for looks. and not only for fittingh tires. there are performance advantages.....

but then again id image most stagea owners really arent worried about handling (not being derrogatory, its 3700 lbs car lol its not ideal)

either way, any of your options are viable, some will look remarkabley differnt than others and fill up the well more.

I'm running 245/45/17, they fit nice, plenty of room inner and outer. And the speedo is more accurate than standard (checked to GPS speedo).

Don't forget ADRs allow speedos to read up to 10% higher than actual speed (so you may be going slower than you think)

I'm running 245/45/17, they fit nice, plenty of room inner and outer. And the speedo is more accurate than standard (checked to GPS speedo).

Don't forget ADRs allow speedos to read up to 10% higher than actual speed (so you may be going slower than you think)

Correct. I found using GPS that my speedo is about 4km/h optimistic, which is good in a way because I at least know that when I think I'm doing a certain speed, I'm actually travelling below it, so I won't get any grief from Cops or speed cameras, etc.

The speedo on my old man's Camry, however, is VERY accurate when compared to GPS readings!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
×
×
  • Create New...