Jump to content
SAU Community

Recommended Posts

Having likely found the wheels to get, now the question of tyre size arises.

OEM tyres on a S2 Stagea is 225/50/16 which gives a diameter of 631.19mm

Looking at 18" x 8" rims

Possible tyre choices (based on 1010tires.com) are:

225/40/18 - diameter of 637.03mm

235/40/18 - diameter of 645.16mm

245/40/18 - diamater of 653.03 (per tyre retailer)

245/35/18 - diameter of 628.65mm

Therefore based on the above, it seems the closest tyre would be the 245/35.18 and then the 225/40/18 (although have noticed in previous threads that the 225/40/18 seems to be the recommended tyre size).

Will check with dealer on the 245/35/18 size. The tyre retailer also stated that the 225/40/18 would be too small in overall diameter whereas the above suggests it is actually a larger diameter than the OEM version.

For those who are running 18" rims (or just know this stuff) can you advise on what tyre sizes you are running and whether you have noticed any problems?

Any help woule be appreciated

Cheers, Al

Link to comment
https://www.sau.com.au/forums/topic/156856-help-with-tyre-sizes/
Share on other sites

if you HAVE to base it on that

I dont listen to tire manufacturers

they tell people things dont work becuase most people are retarded and do stupid things.

225x40

if you want to go lower you can go 215/40

but some people think its unsafe. its not.

But hte need to go with a smaller tire has to do with a few things

First

How low is your car?

Im running small tire sizes becuase i like to tuck tires in my wheel wells.

if you dont need to do that

go with a 245 or so its "Safe" or whatever

but larger tires on 18s looks funny. and it will make your car sit higher.

Edited by yokotas13

Hi Alan,

Pretty sure you are asking the question in regards to keeping your speedo accurate (which is very important in Australia Grant) and you are dead on the money, the 225/40/18 is the closest you can get to the factory rolling distance in a standard 18" tyre. Although the 235/45?/18 is a more common size and can be a lot more cost effective solution without getting too far away from the factory rolling distance.

You can use the following page to work out the difference between the sizes.

http://www.carbibles.com/tyre_bible.html (scroll down a long way).

I have a S1 running 225/40/18 tyres and under the freeway speed check I read 97 when sitting dead on 100km/h so I am happy with that size.

Cheers

Luke

Luke, yeah it is in relation to speedo accuracy to get the closest to the OEM diameter

Logan, my tyre placard has both the 205/55/16 and 225/50/16 on it and I have the 225's on there at the moment

So still divided opinion it seems :)

why is the speedo so important?

Keep a second set of wheel so when inspection comes around, you have a stock rolling diameter wheel.

i do it. its important in japan too

spedo is important here grant because unless u run a gps all the time im buggered if ill fork out the huge dollars for speeding fines here in nsw and believe me ive been done for 5 bloody klm over the limit.not in the stag tho was by a fixed speed cam

As Mike said depending on other things, you can get fined for 2kmh over the limit in WA so having it as close to OEM is a factor over here.

So it seems a toss up between 225 and 235's without any mention of the 245's - would 245's actually fit?

I have 18X8 and 235/40's fitted.

My speedo reads pretty much spot on (+/- 2km/h).

I also am not a fan of the stretched look with tyres. I like it when the edge of the rim and tyre are even. The stretched look just makes it look like you are too cheap to buy a set of proper width tyres (IMHO).

I would have liked 245's, but I heard that they don't fit very well on the front.

but the problem is you guys ar emissing the point and advantages of streching

i wont get into it, but its just not for looks. and not only for fittingh tires. there are performance advantages.....

but then again id image most stagea owners really arent worried about handling (not being derrogatory, its 3700 lbs car lol its not ideal)

either way, any of your options are viable, some will look remarkabley differnt than others and fill up the well more.

I'm running 245/45/17, they fit nice, plenty of room inner and outer. And the speedo is more accurate than standard (checked to GPS speedo).

Don't forget ADRs allow speedos to read up to 10% higher than actual speed (so you may be going slower than you think)

I'm running 245/45/17, they fit nice, plenty of room inner and outer. And the speedo is more accurate than standard (checked to GPS speedo).

Don't forget ADRs allow speedos to read up to 10% higher than actual speed (so you may be going slower than you think)

Correct. I found using GPS that my speedo is about 4km/h optimistic, which is good in a way because I at least know that when I think I'm doing a certain speed, I'm actually travelling below it, so I won't get any grief from Cops or speed cameras, etc.

The speedo on my old man's Camry, however, is VERY accurate when compared to GPS readings!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...