Jump to content
SAU Community

Recommended Posts

you will need to trim the snorkel a bit for it to fit.

as for cutting the reo.. you can always sit the front mount further back but you probably wouldnt be using any 'off the shelf' piping kits as most are designed for the front mount to bolt up to the reo bar.

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 months later...

Sorry to hijack the thread but does anybody have any pics of where their intercooler pipe comes through on the drivers side and over the top of the fan blades or wherever it goes???

Anyone that has installed these lately can you please let me know about the Inlet pipe to the intercooler. It is longer on one side than the other by about 3-5cm.

Does the longer piece connect to the old pipe coming through the hole in the chassis or does it connect to the intercooler inlet?

It seems that either would way might work..

You can cut them after the piping is fitted and the fan still on. Its probably better to do so, so you can check how much needs to be lopped off and check the clearance. As for cutting, we used a pneumatic die grinder with the cutting disc attachment. Or alternatively you could use some tin snips.

We spun the blade around and held a marker in one spot to evenly mark the blades.

Edited by KeyMakeR33
Sorry to hijack the thread but does anybody have any pics of where their intercooler pipe comes through on the drivers side and over the top of the fan blades or wherever it goes???

I gave you photo's of where the hole goes in you other thread.

http://www.skylinesaustralia.com/forums/in...20&start=20

Does anyone Know where to get a smaller type intercooler. I mean thinner like 50mm or something. That might suit this guys application better. I am trying to do the same thing too, i might go for a thinner cooler and try get something that has both outlets on the same side so that I can connect it back up to the factory piping.

Anyone know of places that sell thinner coolers and ones that have outlets on the same side.

Also i am not chasing any big HP figures so i think a thinner cooler might just do me nicely.

Does anyone Know where to get a smaller type intercooler. I mean thinner like 50mm or something. That might suit this guys application better. I am trying to do the same thing too, i might go for a thinner cooler and try get something that has both outlets on the same side so that I can connect it back up to the factory piping.

Anyone know of places that sell thinner coolers and ones that have outlets on the same side.

Also i am not chasing any big HP figures so i think a thinner cooler might just do me nicely.

Just jap have a cooler that has outlets on the same side. I don't think its any thinner though and you would have to get some piping made for you.

I gave you photo's of where the hole goes in you other thread.

http://www.skylinesaustralia.com/forums/in...20&start=20

Oh yeah i know but i mean does anybody have any pics with the pipes in place??

Cheers.

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...