Jump to content
SAU Community

Recommended Posts

Hi guys,

I tried seraching cant find any thing.

I had a CF vented bonnet but too many fines from police prompted me to get an ADR approved fibre glass vented bonnet. MyCF bonnet did no require bonnet pins.

Now my Fibreglass one may require pins if it is not stable at high speed.

Does any one know if pins are illeagle or are there a certain type of bonnet pin that is accepted?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/157737-bonnet-pins-legal/
Share on other sites

Tripych

Yeah thats what i remember too. With that information i dont believe it is possible to have a bonnet pin that sits flush????

Any one know of any?

Yes there are flush sitting bonnet pins, they cost quite a bit though. A lot of the Top Secret cars use 'em. Revolution Racegear in Melbourne sells them. If i remember correctly they were around $100 for the normal ones but slightly more for the set that comes with a tiny key and a small lock built into the pins for security purposes.

Cheers

If I remember correctly the pins aren't allowed to stick out on top of the bonnet. You need something that sits flush with the bonnet as it becomes a hazzard if you hit somebody.

yes which is stupid.. the amount of damage a pin will do or a car..

well alot of these laws are based on pedestrian safety. Some of them do seem stupid but even if we do argue a point alot of the time it falls of deaf ears. I currently drive a gemini which has bonnet pins and haven't had any issues from the police about them. I got in trouble for blue lights on the washer jets but they didn't say anything about the bonnet pins.

Personally I prefer the look of a flush pin over the setup I have on the gemini, I like everything to flow nicely and with big pins sticking out of the bonnet isn't really my taste but that was all I could find when I built the gemini.

I have learnt alot in visual modifications since I had my car and lets just say I am happy I learnt from alot of mistakes on the gemini and when the R32 comes hopefully it will come together alot better.

Link to flush sitting bonnet pins, revolution racegear on the gold coast could get them in stock when I inquired about them 6 - 12months ago. Hope this helps

http://www.vsport.com.au/vsport_aerocatch.htm

Thats a good looking bonnet pin...

lol i think the bonnet pin would be the last thing on the pedestrians mind when being hit by a car

True

True it would be but added injuries that could be sustained from them I think is the reason behind the law. Same sort of deal with wings.

I don't know what happened to this technology but some company was making a system where on a frontal impact it would slightly pop open the bonnet (the edge closest to the windscreen) to try and take away some of the force of the pedestrian hitting the windscreen. When I saw that I just pictued all the "testing gone wrong" where the back of the bonnet pops up sending the test dummy flying over the car :(

Link to flush sitting bonnet pins, revolution racegear on the gold coast could get them in stock when I inquired about them 6 - 12months ago. Hope this helps

http://www.vsport.com.au/vsport_aerocatch.htm

My mate tried to fit these to his R33 about 12months ago, but due to the curve/slop of the bonnet, wasn't able to. The bonnet must be flat to fit these on :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...