Jump to content
SAU Community

Recommended Posts

this is my dream 32 4 door. except it would have to have a stock GTR kit all over it. even the stock rims finish it off nicely.

if i got around to it id make the rear wide body spec like the GTR thoe. not easy when you have a door to include.

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Stock kit going on next month :P and the rear is rolled as far as you can take a 4 door. If you saw how much addon rear guards were for 4 doors, you'd probably choke ;). Although you can get them :(.

Meisters weren't mine and long gone :).

Vivagarge has the rear wide quarters for a 4 door

$480 for both sides

its 4 pieces one on quarter and one on door on each side

they arre 25mm wider

i had seen a set once on yahoo actions but that was it. but 25mm is hardly enough to notice.

i think the best would be to buy the gts to GTR rear guards off car mate. they only go on the lower half of the body work just like the GTR and mate that suit a 4 door.

anyway good luck with it.

  • 7 months later...

While I wait for the GTR bar to go on with Grill (woot finally) I thought I might post an update about the car. Recently got the car tuned down at Status in Victoria and it went from 200rwkw to 245rwkw. Apparently one of the, if not the, highest power out of a 'stock' 26 at 14psi Status has seen :P.

post-15588-1257747144_thumb.jpg

post-15588-1257747163_thumb.jpg

I have cam gears sitting on the passenger seat but was recommended that they are largely a waste of time. And it's getting a lot more road time now :). Also forgot to mention I have since put a Nismo super coppermix twin plate in, awesome clutch.

  • 1 month later...
  • 2 months later...
  • 4 weeks later...
  • 4 months later...
  • 1 month later...

No pics of the interior atm because it's sort of unfinished. And the engine bay isn't particularly exciting because i've gone out of my way to make it stock looking (well except that the covers are all painted blue :blink:). Will try and get something though.

Last weekend at the top of buller sub 3 degree weather fresh after a detail.

IMG_1929800x600.jpg

Copyright Basti.

  • 4 weeks later...
  • 10 months later...

Thought I might give an update.

Car has been good, just fixed up a few annoyances like the power steering setup and mounted the gauges. I've put some brembos on and 33R rims to clear them.

post-15588-0-26780700-1317797035_thumb.jpg

Also transferred a few goodies over to the daily as things get updated :).

post-15588-0-98944700-1317797278_thumb.jpg

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...