Jump to content
SAU Community

Recommended Posts

You guys can all laugh, but there IS a definite relationship.

Basically 6cc per minute per flywheel horsepower is a very close approximation of fuel flow at optimum air fuel ratio.

As you have six cylinders, and six injectors, that means max flywheel horsepower = Injector flow at 100 percent duty cycle.

So basically 550cc injectors would equal 550 flywheel horsepower absolutely flat out at full maximum duty cycle. But that is not real smart. You might want to limit it to 80% duty cycle maybe ? Which would be only 440 flywheel Hp.

But then there are drive train losses, typically only 85% of flywheel power makes it to the rear, so that comes to 374 Hp. Converted to Kw that is 275 RWKw.

Depending on the injectors you run, and assuming the fuel pump is up to the job you CAN figure out a reasonable RWKw versus injector size.

So absolutely balls to the wall with no margin might be injector size in cc x 0.85 x 0.746 = RWKw

Something safer and more reasonable might be injector size in cc x 0.8 x 0.85 x 0.746 = RWKw

Just curious as to what the 0.746 represents, that you have used in your calculations.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just spoke to my tuner and he said there were no issues with the fuel pressure, it was 58psi when it was tuned.

Took the car on a longer trip and it does 11L/100km highway driving and 15L/100km for longish city driving.

The 270rwkw has been confirmed on two different dynos and I have reasonable knock figures (highest I have seen is 40 when really pushing it in 3rd).

Anymore comments?

511rwhp on stock injectors.

it's all about the batch fire....

Sorry, batch fire makes no difference, when duty cycle is 100%, its still 100% if you fire it twice. There is only ways to make more power after you reach the limit of the stock fuel system, raise the pressure, which pushes more fuel through, change the injectors for bigger ones, or get additional fuel elsewhere ie water methanol or auxillery injector.

All the guys making significantly more power than the norm, i dare you to fit the fuel rail and injctors from a stock car and do a power run, the only way to be sure that you injectors are stock is to flow them agaainst known stockers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...