Jump to content
SAU Community

Recommended Posts

I did mine a couple years ago, just purchase your synchro rings(baulk rings) for all gears or just second, third and fourth if youre on a tight budget (since these are the common gears that go). You will probably be better off doing main bearing and front and rear seals too.

Anyhow parts will probably cost you 300-500 depending on what you get. Then take it to gearbox shop and expect shitloads for labour (they are not easy to pull apart whatsoever). But on the upside, as good as new box for maybe a touch more than the second hand one.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2955276
Share on other sites

Here's one I destroyed earlier!!!

Got into first, then second but third went BANG, then it sounded like I was draging a tailshaft under the car.

Got a s/h one and it's been good so far.......

Pull it apart in my carport, just need to buy long gear pullers and a ppg gearset or os gikken!

the insides: enjoy

post-12712-1173104271.jpgpost-12712-1173104328.jpgpost-12712-1173104394.jpg

post-12712-1173104480.jpgpost-12712-1173104559.jpgpost-12712-1173104628.jpg

This happened while I was in Bundaberg.

Changed gbox in front yard.

Pulled it apart in Syd.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2955799
Share on other sites

LOL, I was waiting for someone to bring that up!!

I'll never use that oil again either.

After they put that in it was making a nice bearing whine noise that wasn't there before.

I now use castrol synthetic gear oil and castrol synthetic LSD oil, diff works like new!!!

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2956732
Share on other sites

well i had that decision when my diff went whiny whiny whiny, and i figured its cheaper and keeps my mind at ease KNOWING that your gb has just got all new seals and synchros, and that its gonna hold, and sometimes you might be lucky enough to get warranty. Rather than having a 2nd hand gb which you are unsure about. go the rebuild alot safer

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2957651
Share on other sites

Where do I start!!!

Most are listed in the manual, need alot of drifts supposedly, to put bearings in etc.

spanners

extensions

Socket set

deepsocket set

breaker bar

pin punch set

decent circlip plier set

pitman arm puller

gear puller+ extendable one

Slide hammer to pull out shift rod bearings.(work had one)

rubber mallot

big hammer

A vice to mount the bloody thing on (don't have one yet)!

container and bag to put all the bits in.

clean parts in kerosene.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2959240
Share on other sites

Pm dan from elite racing . i think his username is 3lit3_32

good bloke to deal with. and wont stuff you around.

my opinion is. if your not confident in doing it yourself. let him do it.

i was about 75% confident in being able to do it. but at the end of the day. i have more confidence in him and his warranty on workmanship :)

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2961483
Share on other sites

a pat on the back to the first person to guess what oil GTRsean was running

i know...do you

Hint: some times called. Smurfs Blood

:ninja:

RellikZephyr

Not to get tooo off topic, but heres a good one of an old house mates gearbox when the smurfs blood tried to escape. Only problem was that it was a straight cut box that had been in for 2 weeks or so.

http://www.clubpoint.net/bluebird/gb/Img_2844.jpg

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2962250
Share on other sites

Not to get tooo off topic, but heres a good one of an old house mates gearbox when the smurfs blood tried to escape. Only problem was that it was a straight cut box that had been in for 2 weeks or so.

http://www.clubpoint.net/bluebird/gb/Img_2844.jpg

Nasty!!

Smurfs blood will always look for it's natural environment. It is futile to try and keep it contained in gboxes for too long.

Pitman arm puller is what is used to remove ball joints.

basically two or three adjustable arms with claws on the end and a threaded center bolt with tip.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2962366
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...