Jump to content
SAU Community

Recommended Posts

I did mine a couple years ago, just purchase your synchro rings(baulk rings) for all gears or just second, third and fourth if youre on a tight budget (since these are the common gears that go). You will probably be better off doing main bearing and front and rear seals too.

Anyhow parts will probably cost you 300-500 depending on what you get. Then take it to gearbox shop and expect shitloads for labour (they are not easy to pull apart whatsoever). But on the upside, as good as new box for maybe a touch more than the second hand one.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2955276
Share on other sites

Here's one I destroyed earlier!!!

Got into first, then second but third went BANG, then it sounded like I was draging a tailshaft under the car.

Got a s/h one and it's been good so far.......

Pull it apart in my carport, just need to buy long gear pullers and a ppg gearset or os gikken!

the insides: enjoy

post-12712-1173104271.jpgpost-12712-1173104328.jpgpost-12712-1173104394.jpg

post-12712-1173104480.jpgpost-12712-1173104559.jpgpost-12712-1173104628.jpg

This happened while I was in Bundaberg.

Changed gbox in front yard.

Pulled it apart in Syd.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2955799
Share on other sites

LOL, I was waiting for someone to bring that up!!

I'll never use that oil again either.

After they put that in it was making a nice bearing whine noise that wasn't there before.

I now use castrol synthetic gear oil and castrol synthetic LSD oil, diff works like new!!!

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2956732
Share on other sites

well i had that decision when my diff went whiny whiny whiny, and i figured its cheaper and keeps my mind at ease KNOWING that your gb has just got all new seals and synchros, and that its gonna hold, and sometimes you might be lucky enough to get warranty. Rather than having a 2nd hand gb which you are unsure about. go the rebuild alot safer

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2957651
Share on other sites

Where do I start!!!

Most are listed in the manual, need alot of drifts supposedly, to put bearings in etc.

spanners

extensions

Socket set

deepsocket set

breaker bar

pin punch set

decent circlip plier set

pitman arm puller

gear puller+ extendable one

Slide hammer to pull out shift rod bearings.(work had one)

rubber mallot

big hammer

A vice to mount the bloody thing on (don't have one yet)!

container and bag to put all the bits in.

clean parts in kerosene.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2959240
Share on other sites

Pm dan from elite racing . i think his username is 3lit3_32

good bloke to deal with. and wont stuff you around.

my opinion is. if your not confident in doing it yourself. let him do it.

i was about 75% confident in being able to do it. but at the end of the day. i have more confidence in him and his warranty on workmanship :)

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2961483
Share on other sites

a pat on the back to the first person to guess what oil GTRsean was running

i know...do you

Hint: some times called. Smurfs Blood

:ninja:

RellikZephyr

Not to get tooo off topic, but heres a good one of an old house mates gearbox when the smurfs blood tried to escape. Only problem was that it was a straight cut box that had been in for 2 weeks or so.

http://www.clubpoint.net/bluebird/gb/Img_2844.jpg

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2962250
Share on other sites

Not to get tooo off topic, but heres a good one of an old house mates gearbox when the smurfs blood tried to escape. Only problem was that it was a straight cut box that had been in for 2 weeks or so.

http://www.clubpoint.net/bluebird/gb/Img_2844.jpg

Nasty!!

Smurfs blood will always look for it's natural environment. It is futile to try and keep it contained in gboxes for too long.

Pitman arm puller is what is used to remove ball joints.

basically two or three adjustable arms with claws on the end and a threaded center bolt with tip.

Link to comment
https://www.sau.com.au/forums/topic/158932-5-speed-rebuild/#findComment-2962366
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...