Jump to content
SAU Community

Recommended Posts

usually takes a fair whack of power to turn the starter.

sometimes if you get a flat battery that is drained enough, it doesn't even have enough power to throw out the solenoid in the starter to engage it... (the clicking noise with a 'normal' flat battery)

we get it all the time at work (i work in roadside assistance) where people say "but all the lights on the dash/headlights/etc are working, the engine just won't crank" - 99.99% of the time it is a flat battery.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2970011
Share on other sites

usually takes a fair whack of power to turn the starter.

sometimes if you get a flat battery that is drained enough, it doesn't even have enough power to throw out the solenoid in the starter to engage it... (the clicking noise with a 'normal' flat battery)

we get it all the time at work (i work in roadside assistance) where people say "but all the lights on the dash/headlights/etc are working, the engine just won't crank" - 99.99% of the time it is a flat battery.

I pray your'e right. Thanks for the reply bro.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2970050
Share on other sites

Mine was doing this (sometimes turned over and started instantly) sometimes all it did was 'click' and nothing.

Turns out mine was worn out terminal contacts at the starter motor due to low voltage cranking.

So check battery first to see if it is just an 'almost dead' battery, then move onto the starter motor, including all connections to starter and battery.

A 'relay' was added to my starter to help with the low voltage to starter (although I don't think this was the ultimate solution). I'm going to, when I get the time, replace the positive and negative cables (battery -'ve to block, etc) because I'm thinking my car has a low voltage problem altogether due to poor condition, and size, of these cables. The -'ve cable to the block and negative battery terminal itself looks greasy/dirty and is of small size.

Fixxxer :worship:

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2971346
Share on other sites

usually an alarm won't stop it from cranking though....

what? nearly every immobiliser I know if disables the starter motor... it's usually one of the 3 points of 'cut'. fuel, spark, starter.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2973992
Share on other sites

If it turns out it wasnt your alarm your starter motor could be cactus. Check that its not your battery by turning on the headlights onto something, so you can see them and if they go out when you try to crank your motor then its your battery. if they stay on and only dim a little then its your starter motor...dont know much about the alarms so i hope this helps :nyaanyaa:

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2974281
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...