Jump to content
SAU Community

Recommended Posts

evening fellas

im having a crack at making a pair of length adjustable lower control arms for the front, and im wondering if anyone else has done anything similar. the design itself is pretty straightforward, however im a bit lost on where I can get rose joints, fat high tensile adjustment bolts and nuts ect. anyone (in brisbane mainly) know where i can get some, or better yet, a catalouge on these? Ive had a read of some general industrial parts supplies catalouges but they are pretty slim in this area.

these are r31/s13/r32 style lower arms

Link to comment
https://www.sau.com.au/forums/topic/160148-custom-suspension-arms/
Share on other sites

evening fellas

im having a crack at making a pair of length adjustable lower control arms for the front, and im wondering if anyone else has done anything similar. the design itself is pretty straightforward, however im a bit lost on where I can get rose joints, fat high tensile adjustment bolts and nuts ect. anyone (in brisbane mainly) know where i can get some, or better yet, a catalouge on these? Ive had a read of some general industrial parts supplies catalouges but they are pretty slim in this area.

these are r31/s13/r32 style lower arms

rose joints u should beable to get from a bearing shop (well i know pine river bearings in brendale sells them) as 4 hi tensile bolts try a nut and bolt shop

Just a question... why does it need to be adjustable?

We modified the lower control arms on an AE86 to achieve a higher camber angle on the front. This was made after taking the required measurements to work out the extra length needed. then cut up 2 sets of lower control arms and then welded them together with appropriate reinforcements.

Just a question... why does it need to be adjustable?

We modified the lower control arms on an AE86 to achieve a higher camber angle on the front. This was made after taking the required measurements to work out the extra length needed. then cut up 2 sets of lower control arms and then welded them together with appropriate reinforcements.

why

coz its easier and u can adjust the set up to your needs

as the set ups between street, drift, and drag are all different

funny you should mention pine rivers bearings as thats where i was going to say to get them from....they supply us at work. But any bearing shop should be able to get you rose joints.

yep pine river bearings are great for import bits

they do timing belts and idler and tensioner bearings for ca18 and rb20/25/26 and there as cheap as

why

coz its easier and u can adjust the set up to your needs

as the set ups between street, drift, and drag are all different

Easier?

i can understand the want for adjustability, but if im not mistaken the R31 has not got double wishbone suspension, so adjustment can be fine tuned via a strut top adjuster rather than a lower control arm modification.

Easier?

i can understand the want for adjustability, but if im not mistaken the R31 has not got double wishbone suspension, so adjustment can be fine tuned via a strut top adjuster rather than a lower control arm modification.

like i said it makes the car easier to set up(esp for track work) as in qld u need to get a mod plate and a engineers report if u shortin (buy cutting and welding) any suspension conponments

your right craved r31s use mac struts and you can adjust camber though the top hat, but you cant adjust track. plus adjustability is neat, id hate to make a set of arms up and find out they are way too long or short. im keen on experimenting on what the cars liek to drive with it and with some fiddling to set it right.. plus the whole wanky drift cred yo thing

these arent going in a road car so engineering isnt really a concern.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...