Jump to content
SAU Community

Recommended Posts

HEY boys & girls

long story short.. i need a new engine... my car had an rb20det but yeah it died.. should i get another one.. for about $1000 or sh0uld i get an rb25det? they are newer, bigger & better lol ect.. how much more would i have to pay? $2500 for the rb25?.. has anyone got an rb25 for sale? :laugh: would it go in fine? no problems? :w00t:

and another thing.. i have about.. $3500 BUDGET :ninja: thats for the engine and install ..and prolly one of those major services ect. like timing belt and the oil and fluid top ups ect :rofl: lol i would shout u guys a carton and a good time if u wanted to meet up somwhere and do it all :laugh: i need to get in the circle of LOVE!

im lost without my r324door </3

haha does anyone have a flat bet tow trucK? ... just putting it out there :)

LUB JEZ <o/

Edited by 32JEZ
Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/
Share on other sites

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

following on from the PM's, I would recommend the Rb25 but not sure of whats needed in the gearbox department whether it bolts straight on or not.

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2977750
Share on other sites

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

+ 1. normally all the wreckers sale for 5G.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978280
Share on other sites

I dont know much about the price ranges and acually bolting in the Rb25 but by the sounds of it, if you get a new RB20 and luckily you'll do it right and have some exra dosh over to get some nice upgrades.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978308
Share on other sites

stoking a 20 to a 24 is more effort than it's worth and it's not cheap anyway! With your budget, just stick to putting in a 20 again. You're going to have to pay someone to take it out, someone to put it all back in....and depending on where you go you'll use up your budget quicker than you probably think. Remeber he's not doing any of this himself....I assume? If you're LUCKY you'll have a bit of left over money for some bolt ons.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978673
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...