Jump to content
SAU Community

Gb#2: Jun Spec Crank Collar & Oil Restrictors (x2)


Recommended Posts

Hey all,

I just got off the phone with Matt @ the GTR Shop in New Zealand. I purchased a crank collar and 2 oil restrictors (package deal) for a total of $130AUD delivered.

He told me that the collars are made to JUN specifications and are sought after in bulk from many people in the US with RB engines (10-20 sets a week). Oil restrictors are the same as the ones you would get from Tomei (1.1; 1.2; 1.5mm available)

Matt asked me to put this up as it's easier for him to get something done in bulk than to make 50 trips to the post office...

1-5 sets: $130AUD delivered

5-10 sets: $120AUD delivered

10-15 sets: $110AUD delivered

By "set" - 1 x crank collar; 2 x oil restrictors (any combination)

post-19974-1175554102.jpgpost-19974-1175554098.jpgpost-19974-1175554093.jpgpost-19974-1175554089.jpg

post-19974-1175554079.jpgpost-19974-1175554074.jpg

post-19974-1175554060.jpgpost-19974-1175554055.jpg

post-19974-1175554051.jpgpost-19974-1175554047.jpg

post-19974-1175554069.jpg

This is an EOI only; so if there's enough interest for Matt; I'll organize it.

Interested: 8 (currently at $120AUD each)

N1GTR

Omurru (DELIVERED - 2x 1mm Restrictors)

sky30 (DELIVERED - 1x 1.5mm Restrictor; 1 x 1.25mm Restrictor)

GTR32GUS (DELIVERED - 1x 1.5mm Restrictor; 1 x 1.25mm Restrictor)

2BNVS

humz

gtrtech

Adriano (DELIVERED - 1x 1.5mm Restrictor; 1 x 1.25mm Restrictor)

munro'sgts-t (DELIVERED - 2 x 1.25mm Restrictor)

Thanks

Stan

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Straight from Matt:

We supply grubs screws as a fail safe, but if correct fitting is acheived are not needed other than piece of mind, screws are 5mm

Also interested, this is what I need to run an rb26 pump on an rb30 bottom end right?

Nope, it's for using a wide flange drive oil pump on a narrow flange crank eg; R32GTR N1 oil pump on an RB20/25/30 or early RB26 crank.

:( cheers :)

Nope, it's for using a wide flange drive oil pump on a narrow flange crank eg; R32GTR N1 oil pump on an RB20/25/30 or early RB26 crank.

:P cheers :happy:

Isn't that what I am trying to do? trying to put an 33gtr oil pump (wide flange) on a Rb30 crank (narrow flange)?

Ok so that's 4 sets... need one more :kiss:

BTW I'm still waiting for the one I ordered so shipping from NZ has taken a little bit long.

so is this an actual jun collar or knock off.

ill be buying one of these very soon, once someone can confirm this i could be interested if they arrive soon.

(organiser pm me pls as i wont check here often)

thanx

Humz; Matt from the GTR Shop has advised that this is a JUN spec knock-off - the materials and dimensions are exactly the same (what I've been told anyway)

I'm STILL yet to receive mine but will post up photos as soon as I do.

Just received the following in the mail:

1 x Crank Collar

1 x Grub Screw (black)

1 x 1.50mm Restrictor

1 x 1.25mm Restrictor

I'm not an engine parts expert but they look to be in good form; the machining is pretty good (no rough edges; no barbs etc etc.)

I'll take some photos tonight and post them up :D

Oh BTW; the reason why there is a 1.5 and a 1.25mm restrictor in there is because it comes with 2 and I didn't know what I needed / wanted so I just took the two most common ones :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...